Bosch Appliances MUM8 operating instructions Blender

en

Our	recommendation:						￿	When the height has been set correctly,
- Stirrer:								press Release button(1) and move the
first	stir	in	at	setting	1,	then	setting￿3 or swivel4		arm to	position 6.
- Whisk:							￿ Hold		the whisk and tighten the nut with the
setting 4,			mix	in at	setting 1			enclosed wrench.
- Kneading		hook:					Blender
first	stir	in	at	setting	1,	knead
							at setting￿2
Adding	more		ingredients				If	the	blender	is not included with your
							appliance, you			can purchase one as an

￿Switch off the appliance with the rotary

switch.

optional

accessory.

￿

Remove the cover.

￿

Risk

of injury

from sharp

￿

Press

the

Release button and

move the

￿

blades/rotating

drive

swivel

arm

to position

6.

Never

place hands

in

the

attached

blender!

￿

Add

ingredients

Do not

remove/attach

the

blender￿until￿the

or

drive

is

at a

standstill!

￿ Add

more

ingredients

through

the feed tube

operate

the

blender

empty.

in the

cover.

Never

Blender￿will not work unless the cover has

After

work

been

attached

and

locked.

￿Switch off the appliance with the rotary

	switch.			￿	Risk of scalding		￿
￿	Pull out	the	mains plug.
				When blending hot liquids, steam escapes
￿	Remove	the	cover.
	Tip: To	do this, hold down the release		through the funnel in the cover. Add
	button￿(1)	and remove the cover.		maximum	0,5￿litres of hot or	frothing liquid.

￿Press the Release button and move the

swivel

arm

to

position

6.

Working

with the blender

Fig. 7

Press

the

Release

button(1) and

move the

￿

Take

the

tool

out of the drive.

￿

swivel

arm

to position

3.

￿

Remove

the

bowl.

Remove the blender drive cover.

Clean all

parts, see

•Cleaning

and

￿

￿

servicing".

covers(11 and

12) must be

attached.

Important

information

concerning

￿

Drive

Ensure

that they are

attached

properly

the￿use￿of

the

whisk

Fig. 9

(Fig.￿2a)!

The

whisk

should almost

touch

the

bottom of

Attach

the

blender

(note mark

on the

￿

the

bowl

to

ensure that

the ingredients

are

appliance and on the blender) and rotate as

optimally

mixed.

If small

amounts of

ingredients

possible in

an

anti;clockwise direction

are

to

be

processed,

the whisk

shoulightldy

far as

￿

Add

ingredients.

touch

the

bottom of

the

bowl.

If not,

adjust

the

amount

of

liquid ingredients

height

of

the

whisk as follows:

- Maximum

=￿1.25￿litres;

￿

Pull

out

the

mains

plug.

- Maximum

amount

of

frothing

or hot liquids

￿Press the Release button and move the

swivel	arm		to position		6.	= 0.5	litres;
						- Optimum processing amount of solid
￿ Insert	the		whisk into the drive until the			whisk ingredients		= 150￿grams.
locks	into		position.			￿ Attach the		cover and as	far	as possible
￿ Hold the whisk and loosen the nut with the
enclosed		wrench		(wrench on base).		in￿a￿clockwise direction.
￿ Set the		whisk to the			optimum height by	The lug	on	the blender cover		must be fully
						located	in the slot in the		blender handle!
rotating		the whisk:
						￿ Move the rotary switch to the required
- rotate		to	left:	raise
- rotate		to	right:	lower		setting.

￿Press the Release button(1) and move the swivel arm to position 1.

Check the height of the whisk and, if￿required, correct.

11