Antunes, AJ VS-200aSb owner manual Operation, Operator Controls

Page 10

Variety STeamer

Operation

Operator Controls

Rocker Switch (Power On/Off)

When the Rocker Switch is in the ON position, the control board is activated and the green light on the front panel lights up. A thermostat senses generator temperature. If the generator temperature is below 350° F (176° C), power is applied to the generator until setpoint is reached. The generator is constantly moni- tored and power is regulated to maintain temperature setpoint of 380° F (193° C).

Yellow and green lights

The green light comes on when the Rocker Switch (Power On/Off) is turned on. The green light is not lit during the steaming cycle.

The yellow light comes on during the steaming cycle. When the steaming cycle is complete, the yellow light turns off, and an audio alarm sounds for 3 seconds.

Control knob

The control knob setting determines the length of the steaming cycle. Each number on the panel behind the knob represents a ten second interval (1=10 sec; 2=20 sec; 3=30 sec; etc.) up to 130 seconds.

Example: During the steaming cycle, with the control knob set to 3, the solenoid valve opens once every 10 seconds, applying 3 total shots of water that is con- verted immediately into steam for the product.

NOTE: Each shot of steam is approximately 3/4 oz. (25 milliliters) of water.

Operate switch

When the operate button is pressed and released, Line Voltage is supplied to the solenoid valve, the solenoid valve opens, and water sprays onto the heated steam generator. The water flashes immediately into live steam and is forced up through the Black Manifold Plate orifices.

Lock Lever

When in the full forward (towards operator) position, the lock lever secures the Black Manifold Plate onto the Steam Generator. Moving the lock lever to the full rearward position unlocks the Black Manifold Plate, allowing it to be removed for cleaning or servicing.

 

Operate

 

 

 

Switch

 

 

Green

 

 

 

 

 

Light

 

 

1

2

 

 

13

 

 

 

READY

 

 

3

 

 

12

 

 

4

 

STEAM

11

 

 

5

 

10 9

 

 

Lock Lever

 

8

7

6

Yellow

 

 

 

 

POWER

 

 

 

Knob

Light

 

 

 

 

 

 

 

 

 

 

Control

Audio

 

 

 

 

Knob

 

 

 

 

 

Signal

Rocker Switch

 

 

 

 

(power on/off)

 

Figure 3. Operating Controls

Lock Lever Knob

Locked Position

Figure 4. Lock Lever

Hi-Limit Thermostat

If the generator should overheat for any reason, the Hi-Limit thermostat opens (trips) and cuts off power to the generator. To reset this Hi-Limit, turn the unit off, unplug the power cord, disconnect the rear water line quick disconnect insert, and allow the unit to cool for 45 minutes. Place unit upside down and remove the four

(4)Control Panel screws (Figure 4). Carefully lift the Control Panel upward and lay it on its side. Fully press the red Hi-Limit Reset Button. Reassemble the unit. If the Hi-Limit requires continuous resetting, contact your Authorized Service Agency.

10

P/N 1010649 Rev. E 03/07

Image 10
Contents Variety Steamer Table of contents Owner InformationService/Technical Assistance Model DesignationImportant safety information Electrical Shock Hazard Specifications Equipment Setup InstallationUnpacking Connecting Water Supply Steaming Guide OtherOperation Operator ControlsOperating Instructions Steaming TipsMaintenance Maintenance ScheduleMonthly Cleaning Part Description Qty Variety Steamer Components Troubleshooting Problem Possible Cause Corrective ActionVariety Steamer Wiring Diagram Pictorial Wiring DiagramReplacement Parts Part Description Qty Water Pressure Regulator Kit Part No See page 14 for Strainer Parts identificationVariety STeamer Variety Steamer Limited Warranty