Bosch Appliances PCH 612 DAU Clearances, Minimum flame adjustment, Installation procedure

Page 7

Minimum flame adjustment

1Turn the control knob to minimum.

2Remove the control knob from the valve spindle. Refer Fig. 8.

3Using a screwdriver carefully pry off the hard plas- tic seal. Refer Fig. 9.

4Using a small screwdriver carefully remove the soft rubber seal. Refer Fig. 10.

5The adjustment screw is positioned at the rear lower section of the valve. Refer Fig. 11 & 12.

6To adjust the minimum flame for N.G. replace the control knob onto the spindle, light the gas and turn the control knob to the small flame position. Screw the adjustment screw anti-clockwise to es- tablish a minimum stable flame position. The flame should remain alight and not burn back to the in- jector when the valve is turned quickly from ‘Full On’ to the “Minimum flame” position and back a few times.

Clearances

A range hood fitted above the top must be installed

 

according to the installation instructions for the range

 

hood. A minimum distance of 650 mm is required for

 

a range hood and 750 mm for an exhaust fan.

 

If the distance measured from the periphery of the

 

nearest burner to any vertical surface is less than 200

 

mm, the surface shall be protected in accordance with

 

clauses 5.12.1 & 5.12.1.2 of AS 5601/AG 601.

 

Leave a space at least 100mm between any drawer,

 

partition or oven that is installed underneath the

 

cooktop.

 

Minimum thickness of benchtop is 15mm. See Fig. 2.

2

To adjust the minimum flame position for LP Gas the screw must be fully tightened down clockwise.

7Remove the control knob, replace the seals in re- verse order and refit the control knob.

89

Installation of cooktop into the kitchen bench

Installation procedure:

1. For cutout dimensions and clearances refer Fig 1.

2The hotplate is factory fitted with sealing tape around the lower edge of the hob and two pres- sure clamps front and rear. The seal keeps the en- tire work surface watertight and prevents spillage from leaking into cupboards underneath. Please ensure that the sealing tape is not disturbed during the installation process. Refer Fig. 3.

1011

12

3

3Place hotplate on top of the bench cut-out and press down firmly on all edges at the same time to en- sure that the hob is resting on its entire perimeter.

NOTE: If it is necessary to dismount the hob, press upwards only from underneath.

10

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model No’s PCH 612 DAU BoschService agent Wiring diagramSwitch Blue wire Brown wire Terminal Ignition module Contents ServiceDo’s Safety considerationsFor your safety What to do if you smell gas CleaningWok trivet Wire coffee supportUser instructions Boiling burnersBurner locations InstallationPreparing to install Operating instructionsInstallation procedure Minimum flame adjustmentClearances Gas ConnectionConverting the cooktop from Nat. Gas to Propane Gas Electrical

PCH 615 DAU, PCH 612 DAU, PCH 615 FAU specifications

Bosch, a renowned brand in the home appliance industry, consistently delivers high-quality products designed to enhance the comfort and efficiency of modern living. Among their impressive range, the Bosch PCH 612 DAU, PCH 615 DAU, and PCH 615 FAU stand out with their innovative design, advanced technologies, and user-friendly features, making them ideal choices for contemporary kitchens.

The Bosch PCH 612 DAU is a built-in gas hob that is distinguished by its sleek design and high performance. One of its main features is the inclusion of four gas burner zones, which provide flexibility for different cooking styles. The burners are equipped with a flame failure safety device, ensuring that the gas supply is cut off in case the flame goes out, enhancing safety during cooking. The hob's tempered glass surface not only offers a modern aesthetic but also makes it easy to clean.

Moving to the Bosch PCH 615 DAU, this model further elevates the cooking experience with five gas burners, including a high-efficiency burner that delivers rapid heat for quicker meal preparation. The PCH 615 DAU is designed with control knobs positioned at the front, allowing for easy access while cooking. The pan supports are made of cast iron, which not only add stability but also provide excellent heat retention. The model also boasts a unique auto-ignition feature, making it convenient to use with just one hand.

The Bosch PCH 615 FAU is a cutting-edge induction hob that revolutionizes the way we cook. Featuring four heating zones with a powerful boost function, the PCH 615 FAU reduces cooking time significantly. The induction technology provides precise control over cooking temperatures, allowing for perfect results every time. Safety features are prominent in this model, including a child lock and automatic switch-off, ensuring peace of mind for families. The hob's sleek black glass finish complements any kitchen decor while making maintenance a breeze.

All three models embody Bosch’s commitment to sustainability and energy efficiency. They are designed to minimize energy consumption without compromising performance. The intuitive control interfaces across these hobs ensure that users can easily manage their cooking environments.

In summary, the Bosch PCH 612 DAU, PCH 615 DAU, and PCH 615 FAU exemplify innovation and functionality in modern kitchen appliances. With their advanced features, safety technologies, and stylish designs, these hobs cater to both novice and experienced cooks alike, making them valuable additions to any home. Whether you prefer gas or induction cooking, Bosch provides exceptional options tailored to meet diverse culinary needs.
Top Page Image Contents