Integra Cycle Complete Signal

If you wish to r_set the cycle to its beginning after stopping the dishwasher:

1.Close the door of the dishwasher, Make sure that the door is completely closed and latched.

2.Depress the on/off button, then depress both POWER SCRUB PLUS and REGULAR WASH

buttons at the same time and hold for approximately 3 seconds. The cycle progress lights will jump to the end and the "CLEAN" light will become illuminated. When the drain pump has stopped and the "CLEAN" light is illuminated the cycle is at the end and the dishwasher is reset.

3.Depress the on/off button to shut-off the dishwasher.

4.The dishwasher is now ready to run your selected

wash cycle. Depress on/off button to restart the dishwasher.

Note: If you wish to change the cycle selection simply depress the button of the cycle desired twice. The light above that cycle will then become illuminated to show it has been selected.

TO START THE SItV 4300, SHV 4800, and SHU 9900

Once detergent has been added and before closing the door of the dishwasher check the wash arms to ensure

that they are free to move.

NOTE: The following sequence must start with the on/off switch in the "off" position (up).

•Before closing the door of the dishwasher depress the on/off switch to the "on" position. The indicator light labeled "Clean" will become illuminated.

•Depress the button for the cycle you desire.

NOTE: For the SHV 4800 series you also have the option of washing in the top rack only. Depress the "Top Rack Only" button and the button of the cycle desired, both should be illuminated. Wash

action will ONLY be provided by the upper spray arm. Do not load dishes or silverware in the lower

rack.

•Close the door and the dishwasher will start

automatically and continue until the end of the selected cycle.

"At the end of the cycle the dishwasher will stop. When the door is opened the clean light will become illuminated (the lights are not illuminated when the door is closed).

•At the completion of each wash cycle you must depress the on/off switch to reset the controls. If

you inadvertently forget to depress the switch, you must turn the unit off for five seconds before

starting the next wash sequence.

The SHU 9900 model has a Cycle Completion Signal. At the end of a wash cycle, the beeper will sound off two times, and again every 15 minutes until the dish- washer is tamed off. To disable or enable the Cycle Completion Signal, you need to first set the dishwasher

in program mode. To do this, hold down the "Quick

Wash" button and simultaneously depress the On/Off button to the "on" position. The "Quick Wash" button's light will start to blink. This means that the washer is in "program mode". While the light is still blinking, push the "Quick Wash" button. If the machine beeps, then the Cycle Completion Signal has been enabled (turned on). When you push the button again and it doesn't beep, it means that the Cycle Completion Signal has been disabled (turned off). After you have chosen to disable or enable the beeper, you need to depress the On/Off button to the "off" position to take it out of program mode. Now you are ready to continue with your regular wash cycle.

TO INTERRUPT A WASH CYCLE

Open the door just enough for the interlock switch to disengage and shut the machine off. Wait for the motor noises to stop. After opening the door leave it ajar for a few minutes before resuming operation. The cycle can be resumed by closing the door.

TO RESET THE CYCLE

•Open the door just enough for the interlock switch to disengage and shut the machine off. Wait for the motor noises to stop.

•Depress the "Regular Wash" and "Power Scrub Plus" buttons at the same time and hold for

approximately 3 seconds. Close the door and the drain pump will run for approximately 60 seconds. This will remove any water in the unit.

•The cycle has now been reset to the end of the wash program and the "Clean" light will be illuminated.

•As always you must depress the on/off switch after opening the door in order to reset the cycle to the beginning.

DO NOT PULL DOOR FULLY OPEN WHILE DISHWASHER IS IN OPERATION.

QUICKLY OPENING THE DOOR WHILE DISHWASHER IS IN OPERATION COULD RESULT IN SERIOUS SCALDING.

UNLOADING

When unloading the dishwasher always unload the lower rack first and then unload the upper rack. This will minimize the chance of water drops from the upper rack falling on the dishes in the lower rack. The silverware basket(s) of the Bosch dishwasher may be removed for easy unloading.

Also, when unloading, it is recommended that the dishes be allowed to cool before handling. The dishes will cool more quickly if the door is opened slightly.