Grundig cirflexx UMS 5400 DEC manual General information on laser devices, Troubleshooting

Page 36

CLASS 1

LASER PRODUCT

INFORMATION_____________________________________

General information on laser devices

Your system is a CLASS 1 LASER PRODUCT. This means that the laser is designed in such a way as to ensure that the maximum permissible emission value cannot be exceeded under any circumstances.

Caution:

If operating devices or methods other than those specified here are employed, it may lead to danger- ous exposure to emissions.

This device emits laser radiation. Because of the danger of eye injuries, the unit may only be opened or serviced by trained personnel.

If settings other than those specified here are employed or other procedures are carried out, this may lead to dangerous radiation exposure.

Troubleshooting

Not every kind of sound interference is caused by a defect in your hi-fi system. Defects can also be caused by leads having been accidentally pulled out, damaged CDs and worn out batteries in the remote control. If the following measures do not rectify the problem, consult an authorised dealer.

Fault

Possible cause/remedy

 

 

No sound.

The volume setting is too low – increase the volume.

 

The headphones are plugged in – disconnect the

 

headphones.

 

The power cord is incorrectly connected. Connect it

 

properly.

 

Mute is activated, deactivate Mute.

 

 

The hi-fi system does not react when

Static electrical discharge. Switch off the hi-fi system,

the buttons are pressed.

disconnect the power cable and plug it in again after a

 

few seconds or press »RESET«.

 

 

The remote control does not work.

The batteries are flat. Replace the batteries.

 

The remote control is out of range of the stereo.

 

 

Poor radio reception.

Weak antenna signal, check the antenna.

 

Weak FM-stereo signal, switch to Mono.

 

Interference from electrical devices such as televisions,

 

video recorders, computers, neon lamps, thermostats or

 

motors. Keep the hi-fi system away from such devices.

 

 

Tracks on a CD are skipped.

The CD is damaged or dirty – replace the CD or clean it.

 

The PROGRAM (track memory) or RANDOM functions are

 

active. Deactivate the functions.

 

 

CD-Rs or CD-RWs are not played

Faulty software or hardware settings during burning or the

back, or are played back incorrectly.

CD itself.

 

Check the components of your CD burner/software or

 

change the CD being used.

 

 

36

Image 36
Contents Hifi Micro System Set-up and safety SettingsTuner mode CD modeSET-UP and Safety Environmental noteHi-fi system controls Controls on the frontTuning AlbumControls on the top Reset Controls on the bottomSD/MMC USB000000 Hi-fi system displaysFile w Back of the hi-fi system AntennaAUX in L SpeakerRemote control PTYColor BrightnessFM Mode DisplayINTRO/REP PROG./RANDConnecting the antennas Connecting the loudspeakersConnecting the power cord Inserting batteries in the remote control Connecting the headphonesConnecting an external device Connecting an MP3 player or a USB memory stick Inserting a memory cardRemoving the memory card Setting the time 1202003 1203Setting and storing radio channels Automatic station search ASPAutomatic station search Manual station searchResetting the hi-fi system Storing stations as presetsSwitching on and off Adjusting the brightness of the displayAdjusting the volume Changing the colour of the display lightingSetting the equaliser Switching the Ultra Bass System on and offSwitching the display Selecting sound effectsSelecting a preset channel Selecting the Tuner input sourceStereo/mono reception Automatic station search ASPRDS station service Searching for RDS stationsRDS time synchronisation Viewing RDS information1320 Programme types PTYCD Mode Selecting the CD input source009 115Inserting a CD Playing back a CD001 000Repeating a file or a track Repeat One Repeating all the files on an album MP3 onlyRepeating all files or tracks Repeat All 006 Playing back files or tracks in random order RandomPlaying the introductions of files or tracks Intro Prog Creating a track memorySelecting and storing files MP3 only Selecting and storing tracks CD-DA only070 Checking the track memoryAdding files or tracks Deleting the track memoryPlaying the contents of a memory card Playing the contents of an MP3 player or USB Memory stick1431 1645Switch-on timer Setting the switch-on timer000 600 630 1445 18492316 Reminder timer Sleep timer0934 2359Cleaning the CD unit Technical dataTroubleshooting General information on laser devicesGrundig Multimedia B.V