Panasonic KX-TDA100 Prepare the CS for site survey, Using the KX-TD7684/KX-TD7694

Page 184

2.9.2 Procedure Overview

2.9.2 Procedure Overview

When connecting the wireless system, use extreme care in conducting the site survey. An incorrectly performed site survey can result in poor service area, frequent noise, and disconnection of calls.

1. Investigate the installation site

Refer to "2.9.3 Site Planning".

a.Obtain a map of the CS installation site.

b.Identify the service area required by the user on the map.

c.Plan the location of each CS, taking account of distance, building materials, etc.

2. Prepare the CS for site survey

Refer to "2.9.4 Before Site Survey".

a.Assign a CS number to each CS by setting the DIP switches on the back of the CS.

b.Supply electricity to each CS using an AC adaptor/battery box or by connecting them to a CSIF/DLC/ DHLC card.

c.Install each CS temporarily as planned.

Note

Install at least 2 m above the floor.

Keep the antennas in the upright position.

3. Conduct the site survey

Refer to "2.9.5 Site Survey".

a.Test the radio signal strength using the PS.

Confirm that the radio signal strength level is "12" near the CS.

Using the KX-TD7684/KX-TD7694

Display example:

1

9

0

CS No.

<< SEARCHING >>

CS NO.1 LEVEL:12

Press 1, 9, and POWER

1 to 9

for more than 2 seconds.

 

Using the KX-TD7680

1

9

0

CS No.

 

Press 1, 9, and POWER

 

1 to 9

for more than 2 seconds.

 

 

Display example:

<< SEARCHING >>

SAVE:0123456789

CS NO.1 LEVEL:12 SAVE:0123456789

Using the KX-TD7690

19

Press 1, 9, and POWER for more than 2 seconds.

CS No.

1 to 9

Display example:

<< SEARCHING >>

CS NO.1 LEVEL:12 SAVE:0123456789

184

Installation Manual

Image 184
Contents Hybrid IP-PBX Model No. KX-TDA100System Components Table Category Model No ShelvesMain Processing Card MPR Option Card Trunk CardsPower Supply Units Category Model No Extension CardsOther Cards Optional SD MemoryCompatible Panasonic Proprietary Telephones Equipment CompatibilityIncompatible Panasonic Proprietary Telephones Safety Notices List of AbbreviationsImportant Safety Instructions For All Telephone Equipment For the PBXGHz Cell Station Only for KX-TDA0151CN Dect Cell StationDect 6.0 Cell Station What is User Information?Requirements For the PBX For users in the United Kingdom This appliance must be earthedFor users in the European Union only For users in Germany onlyFor users in New Zealand only For business users in the European UnionFor users in Australia only For users in Taiwan onlyStructure of this Manual About the Other ManualsAbout the software version of your PBX TrademarksTable of Contents Information about the Other Cards 124 Connection of Extensions 138Connection of Dect Portable Stations 151 Connection of 2.4 GHz Portable Stations 182245 249252 253Table of Contents Section System Outline System Highlights System HighlightsPortable Station PS Features PC Phone/PC Console FeaturesHospitality Features Built-in Simplified Voice Message SVM FeaturesBasic Shelf Basic System ConstructionConstruction of the Basic Shelf System Connection Diagram PBXMountable Equipment Optional Equipment Optional EquipmentModel Name Model No KX-TDA0290CE/ KX-TDA0290CJ Specifications General DescriptionDimension Weight when fully mounted KX-TDA100 KX-TDA200Characteristics Cards Installed in the Slots of the PBX Maximum Optional Service CardsSystem Capacity Trunk Card Total 6*1 Total 8*2 Extension Card Total Cards Mounted on Other Optional Service Cards Mounted onMaximum Terminal Equipment MEC Card Calculation MEC Card CalculationCalculation Example KX-TDA100 Equipment Type MEC FigureLoad Figure Calculation Power Supply Unit SelectionPSU Capacity Calculation Example KX-TDA200 Section Installation Before Installation Before InstallationSafety Installation Instructions Installation PrecautionsBefore Installation Installation of the PBX UnpackingNames and Locations Inside ViewOpening/Closing the Front Cover Opening the Front CoverClosing the Front Cover Installing/Replacing the Power Supply Unit Accessories and User-supplied ItemsSafety Instructions FunctionInstalling the Power Supply Unit Replacing the Power Supply Unit Replace the PSU Frame Earth Connection Backup Battery Connection Backup Power Supply DurationConnecting Backup Batteries User-supplied ItemsBattery Switch Battery Connector Installing/Removing the Optional Service Cards Installing Optional Service CardsInstalling/Removing the Optional Service Cards Covering the Blank Slots Handling of the Cables Removing the Optional Service Cards Types of Connectors Connector Type Pin Number Used forUSB MPR Attaching a Ferrite Core Attaching to an RJ45 ConnectorFor T1/E1/PRI/IP-GW16/IP-EXT16 Cards For a BRI Card Attaching to an Amphenol Connector For Extension CardsFastening Amphenol Connector Amphenol Connector Pin Assignment Chart DID8 DHLC8 DLC8 DLC16Wall Mounting KX-TDA200 Wall Mounting KX-TDA200 Wall Mounting KX-TDA100 WallWall Mounting KX-TDA100 Floor Standing KX-TDA200 Only TOP Front Installation Surge Protector InstallationOverview Outside Installation Installation of an Earth RodSurge Protector Installation Information about the Main Processing Card MPR CardIndication LED IndicationsColour MEC Card KX-TDA0105 RMT Card KX-TDA0196 Information about the Trunk Cards Amphenol Connector Signal Name FunctionSignal Name Pin Assignments2 DID8 Card KX-TDA0182 LED Indications Switch Settings on LCOT8/LCOT16 cards Switch3 CID/PAY8 Card KX-TDA0189 Type4 CID8 Card KX-TDA0193 5 E&M8 Card KX-TDA0184 T1C T1D T1E T1F T1G T1H Switch Type Switch Settings6 T1 Card KX-TDA0187 RJ45 Connector for Extension Use RJ45 Connector for Trunk UseLevel Function Maximum Cabling Distance of Extension Connection 7 E1 Card KX-TDA0188 BNC coaxial Connector TX Signal Name Level FunctionBNC coaxial Connector RX 8 BRI4 Card KX-TDA0284 and BRI8 Card KX-TDA0288 TX1 RX2 RX1 TX2 Line LED Pattern LayerMaster Clock LED PatternMaximum Cabling Distance of S0 Bus Connection 9 PRI30 Card KX-TDA0290CE/KX-TDA0290CJ Termination Card Status SYNC-ERR RAI AIS Sync Link 10 PRI23 Card KX-TDA0290 100 Installation Manual Sync Link IP-GW4 Card KX-TDA0480 RJ45 Connector 10BASE-TInput I/Output O Function Card Status Online Alarm IAM Busy Link Data COL Siosel RJ45 Connector 10BASE-T/100BASE-TX IP-GW4E Card KX-TDA0484Card Status Online Alarm IP-GW16 Card KX-TDA0490 Installation Manual 107 Information about the Extension Cards CSIF4 Card KX-TDA0143 and CSIF8 Card KX-TDA0144RJ45 Connector DHLC8 Card KX-TDA0170 D1BD1C 3 DLC8 Card KX-TDA0171 D2C 4 DLC16 Card KX-TDA0172 Installation Manual 115 5 SLC8 Card KX-TDA0173 Indication Colour EXT-CID Card KX-TDA0168 Installation Manual 119 120 Installation Manual Installation Manual 121 IP-EXT16 Card KX-TDA0470 Installation Manual 123 Information about the Other Cards 1 OPB3 Card KX-TDA0190User-supplied not included Copper wire 2 DPH4 Card KX-TDA0161Pin Terminal Block 3 DPH2 Card KX-TDA0162 Proprietary Signal Name Standard Signal NamePath Doorphone Call Path 4 EIO4 Card KX-TDA0164 C4b C4a C3b C3a C2b C2a C1b C1a External Sensor Connection DiagramExternal Relay ECHO16 Card KX-TDA0166 6 MSG4 Card KX-TDA0191 ESVM2 Card KX-TDA0192 and ESVM4 Card KX-TDA0194 CTI-LINK Card KX-TDA0410 Card Status Link Status PT-interface CS Connection of ExtensionsDSS Console Indicates that the extension card supports the terminal With APT Parallel Connection of the ExtensionsWith DPT Using an EXtra Device Port Using a Modular T-AdaptorWith KX-DT300 Series DPT except KX-DT321 With KX-T7600 Series DPT except KX-T7665 With Other DPT except KX-T7560 and KX-T7565With KX-DT300 Series DPT Digital EXtra Device Port Digital XDP ConnectionBack View of DPTs To Main Unit To TEL Pabx With KX-T7600 Series DPT except KX-T7600E Series To Main Unit Pabx146 Installation Manual With KX-T7600E Series DPT Connecting to a Slave DPT Connecting to a Master DPT KX-DT343/KX-DT346 First Party Call Control CTI ConnectionKX-T7633/KX-T7636 RF Specification Connection of Dect Portable StationsOverview Required Equipment and Maximum Number of CallsFrequency Band Number of CarriersCarrier Spacing Bit RateProcedure Overview Investigate the installation sitePrepare for site survey Conduct the site surveyConnect the CS and PS to the PBX and test the operation Finish the site surveyMount the CS on the wall Site Planning Characteristics of Radio WavesUnderstanding Radio Waves Object Material Transmission TendencyCS Coverage Area Radio Signal Strength LevelsSite Survey Preparation CS installation plan Example Installing in a Room Separated by Interior WallsThings to take note Using the KX-TCA255/KX-TCA256/KX-TCA355 Before Site SurveyChecking the CS ID Number Assigning the CS ID Number to the PSUsing the KX-TD7590 Setting and Installing the CS Temporarily for Site Survey DIP SwitchOFF on KX-TDA0158CEKX-TDA0141CE/KX-TDA0142CE Testing the Radio Signal Strength To survey other slotsPS CH0 Referring to the Stored Scan Data Log NoClearing the Stored Scan Data After Site Survey Connecting a Cell Station to the PBX Using a Csif CardAccessories and User-supplied Items for the CS User-supplied not included RJ11 connectorUsing a DHLC/DLC Card KX-TDA0141CE Connecting the CS For the KX-TDA0142CE User onlyInstallation Manual 173 Entering the PBX System Programming Mode Using a PT Using the KX-TCA155/KX-TCA255/KX-TCA256/KX-TCA355Registering the PS PS RegistrationSystem Lock Password Using the KX-TD7580System Lock Password /OK Setting the PIN for PBX Using the KX-TCA155/KX-TCA255/KX-TCA256/KX-TCA355Using the KX-TD7580 Changing the Display Language of the PSIf the registration information is still stored in the PS Testing the OperationHandset PIN Wall Mounting Mounting the KX-TDA0158CEInstall a screw here 83 mm Reference for Wall Mounting KX-TDA0158CEMounting the KX-TDA0141CE/KX-TDA0142CE Install a screw here 71 mm Reference for Wall Mounting KX-TDA0141CE/KX-TDA0142CEConnection of 2.4 GHz Portable Stations Installation Manual 183 Using the KX-TD7684/KX-TD7694 Using the KX-TD7680Using the KX-TD7690 Prepare the CS for site surveyInstallation Manual 185 Object Installation Manual 187 188 Installation Manual KX-TDA0151CN 100 m KX-TDA0151CN 50 m Installation Manual 189 OFF KX-TDA0151/KX-TDA0152KX-TDA0141/KX-TDA0142 KX-TDA0151/KX-TDA0152KX-TDA0141/KX-TDA0142 Site Survey Scan Data No CS NoPS CS NO.1 LEVEL12 Scan Data No Deleting the Stored Scan Data Scan Data NoKX-TDA0151/KX-TDA0152 KX-TDA0141/KX-TDA0142 KX-TDA0152/KX-TDA0142 KX-TDA0151/KX-TDA0141 200 Installation Manual Entering the System Programming Mode When the PS has not been registered yet Using the KX-TD7684/KX-TD7694Using the KX-TD7680 Using the KX-TD7690Setting the System Lock Setting the PIN for PS Using the KX-TD7684/KX-TD7694 692System Mounting the KX-TDA0151/KX-TDA0152 Installation Manual 207 Reference for Wall Mounting KX-TDA0151/KX-TDA0152 Mounting the KX-TDA0141/KX-TDA0142 Reference for Wall Mounting KX-TDA0141/KX-TDA0142 Connection of Dect 6.0 Portable Stations Names and Locations of CSRadio Access Method Number of Carriers Carrier SpacingUsing the KX-TD7685/KX-TD7695 214 Installation Manual Installation Manual 215 216 Installation Manual Installation Manual 217 218 Installation Manual Using the KX-TD7685/KX-TD7695 KX-TDA0155 KX-TDA0158 KX-TDA0155 KX-TDA0158 Installation Manual 223 224 Installation Manual PS CH0 L12 226 Installation Manual Installation Manual 227 KX-TDA0155KX-TDA0158 Installation Manual 229 D1B D1A Connect the cable from the PBX to the CS Setting the PIN for PS PIN for PS Registration 691 If Rejected or Time out is displayedMounting the KX-TDA0155/KX-TDA0158 236 Installation Manual Install a screw here 100 mm 83 mm Reference for Wall MountingInstalling the Doorphone KX-T30865/KX-T7765 Maximum Cabling DistanceInstallation Manual 239 Connection Connection of Peripherals Connection of PeripheralsConnection Charts PagerPC/Printer via RS-232C Pin AssignmentsFor connecting a printer/PC with a 25-pin RS-232C connector RS-232C SignalsPC/CTI Server via USB version Power Failure Connections Power Failure ConnectionsUsing Analogue Trunk Card and Extension Card RJ11 Connector Pin Assignments for Analogue Trunk CardPFT Ports 3 and 4 for LCOT16 card only Signal Name Function RJ11 Connector Pin Assignments for Extension CardPFT Ports 1 Signal Name Function Switch Settings Using BRI CardRJ45 Connector Line 1 Pin Assignments RJ45 Connector Line 2 Pin Assignments Starting the PBX System Initialisation ProcedureStarting the PBX Confirming the Trunk Connection Guide for the Maintenance Console Overview PC Connection PC ConnectionSerial Interface Connection LAN Connection via CTI-LINK CardExternal Modem Connection RD RXD SD TXD ER DTR DR DSRInstallation of the Maintenance Console Installing and Starting the Maintenance ConsolePassword Security System RequirementsPage When country/area data do not match Select KX-TDA100/200 from PBX Model258 Installation Manual Section Troubleshooting Troubleshooting InstallationCause Solution ConnectionTrunk is connected to the T2/R1 Operation 264 Installation Manual Installation Manual 265 Using the Reset Button OperationError Log Display Format Troubleshooting by Error LogDescription Sub Code Error Message Log Information Appendix Changed Contents Revision HistoryPmpr Software File Version New OptionsInstallation Manual 271 272 Installation Manual Installation Manual 273 New Contents Index Numerics KX-TDA0173 8-Port Single Line Telephone Extension PSU Reference for Wall Mounting Page Installation Manual 281 For Future Reference
Related manuals
Manual 194 pages 61.97 Kb Manual 248 pages 58.62 Kb Manual 40 pages 36.33 Kb Manual 58 pages 2.3 Kb Manual 194 pages 61.15 Kb

KX-TDA100 specifications

The Panasonic KX-TDA100 is a versatile digital hybrid telephone system designed to meet the communication needs of small to medium-sized businesses. This system blends traditional telephone functions with advanced digital technology, making it an excellent choice for organizations looking to enhance their telecommunications infrastructure.

One of the key features of the KX-TDA100 is its ability to support both digital and analog telephony, allowing businesses to integrate existing telephone lines and devices with newer technologies. The system can accommodate up to 100 extensions, making it scalable and suitable for growing businesses. Additionally, it supports a variety of communication services, including voice mail, computer telephony integration, and automatic call distribution, which enhances customer service capabilities.

The KX-TDA100 utilizes advanced digital signal processing technology, ensuring clear and reliable communication. It employs features such as call forwarding, caller ID, call waiting, and conference calling, which improve productivity and streamline communication among team members. The system also allows for the integration of mobile devices through its support for SIP trunking, enabling seamless communication even when employees are on the go.

Furthermore, the KX-TDA100 includes built-in voicemail functionality, allowing businesses to manage messages efficiently. The voicemail system supports features like voicemail-to-email, which provides users with immediate access to their messages, and the option to customize greetings and auto-attendants that enhance caller experiences.

Security is another critical aspect of the KX-TDA100. The system offers various security features to protect against unauthorized access and ensure data integrity, including encryption and secure network protocols. This attention to security makes it suitable for businesses that handle sensitive information.

Overall, the Panasonic KX-TDA100 combines flexibility, scalability, and advanced technology, making it an ideal solution for businesses looking to improve their communication systems. Its user-friendly design, robust feature set, and ability to grow with the organization make it a reliable choice for enhancing productivity and ensuring effective communication within teams and with customers. Whether deploying for day-to-day operations or accommodating remote work, the KX-TDA100 offers the reliability and features that modern businesses require.