Lincoln 1155-000-EA, 1154-000-EA, 1164-000-EA service manual With Power on and Thermocouple

Page 14

 

 

connected to the oven control, and the display indicates

 

 

“PROBE FAIL”, disconnect the thermocouple from the

 

 

oven control and measure the resistance of the

 

 

thermocouple. The thermocouple should read approx.

 

 

11Ω. If these readings are not achieved, replace the

 

 

thermocouple. If these readings are correct, proceed.

 

Oven control

If the thermocouple checks good, but the oven control

 

 

indicates that there is a thermocouple failure, replace

 

 

the oven control. If the oven control indicates a

 

 

temperature reading but the oven will not heat,

 

 

proceed.

 

Thermocouple

WITH POWER ON AND THERMOCOUPLE

 

 

ATTACHED TO THE OVEN CONTROL: Measure the

 

 

DC millivolt output of the thermocouple. Refer to the

 

 

thermocouple chart (located in the “Removal” section of

 

 

the manual) for proper millivolt readings. If these

 

 

readings are not achieved, replace thermocouple.

 

Oven control

If the thermocouple checks good, but there is no supply

 

 

voltage output to the mercury contactor, replace the

 

 

oven control. If there is supply voltage output to the

 

 

mercury contactor, proceed.

 

Mercury contactor

Check for supply voltage to the contactor coil. If voltage

 

 

is present and the contactor will not activate, replace

 

 

the mercury contactor Also check each contactor for

 

 

high voltage input and output.

 

Heating element(s)

Check the Amp draw on each power leg for proper

 

 

load. Check the specification plate for rating

 

 

information. If the Amp draw is high or low, check the

 

 

individual elements for opens, shorts and proper

 

 

resistance.

 

 

WITH POWER OFF; To check resistance of the

 

 

elements, remove all leads from the elements and use

 

 

a digital multimeter.

 

 

The element resistance should be as follows:

 

 

230V – 33 ohm.

 

 

Replace heating elements as needed.

Oven heats with

Mercury contactor

The mercury contactor has probably failed in the closed

switch off

 

position. If there is no voltage at the operating coil, but

 

 

there is high voltage output from the contactor, replace

 

 

the mercury contactor.

Intermittent heating

Thermal/overload of

The main fan motor is equipped with internal thermal

 

main fan motor

protection and will cease to operate if overheating

 

 

occurs. As the motor overheats and cools, this will

 

 

cause the heating system to cycle on and off

 

 

intermittently. Improper ventilation or lack of preventive

 

 

maintenance may cause this problem. Also, most of the

 

 

problem listed under “Oven will not heat” can cause

 

 

intermittent failure.

Conveyor will not run

Incoming power supply

Check breaker, reset if required. Check power plug to

 

 

be sure it is firmly in receptacle. Measure incoming

 

 

power, call power co. if needed.

 

Fuse, 10 amp

Check, replace if necessary.

 

Fuse holder

Check, replace if necessary.

 

Hi-limit thermostat, control

Check for voltage on both sides of switch. Terminals are

 

box

normally closed. If open, reset and test oven for proper

 

 

operation. If thermostat will not hold, and control box

 

 

temperature is not exceeding 140°F (60°C), replace

 

 

thermostat.

 

Switch, main fan

With power off, check continuity between switch

 

 

terminals. Replace as needed.

14

Impinger II – Advantage Digital Service Manual - International

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Impinger Advantage Digital Series LP GAS PhaseNAT. GAS Power Supply Main FAN Circuit Heat Circuit Conveyor Control Schematic Diagram Serial Number 2045408 and Above Serial Number 2038616 and Above Schematic Diagram NAT. GAS Page Page Belt JAM Refer to Proper Schematic for Identified Components Page With Power on and Thermocouple Belt JAM ON/OFF Switch Replacement MOTOR, Main FAN ReplacementCapacitor Replacement Impinger II Advantage SeriesCooling FAN, Control BOX Replacement Fuse Holder ReplacementTHERMOSTAT, Control BOX HI-LIMIT Replacement THERMOSTAT, Cooling FAN, ReplacementThermocouple Replacement TRANSFORMER, Control ReplacementOven Control Replacement Thermocouple Measurement Temperature F MillivoltsPage Bypass Orifice Replacement Temperature Regulation Valve ReplacementIGNITER/SENSOR Assembly Replacement Main Burner Orifice ReplacementBEARING, Conveyor Replacement CAPACITOR, Conveyor Drive Motor ReplacementAIR Pressure Switch Replacement Mercury Contactor ReplacementImpinger II Advantage General View Letter Part Number DescriptionPage Impinger II Advantage Control BOX 1154-000-EA, 1155-000-EAPage 1164-000-EA Page Oven Back Assembly Page Conveyor / Door

1155-000-EA, 1164-000-EA, 1154-000-EA specifications

Lincoln Electric is a renowned name in the welding and cutting industry, and its products, especially the Lincoln 1164-000-EA, 1154-000-EA, and 1155-000-EA, represent the company's commitment to innovation and performance.

The Lincoln 1164-000-EA is particularly distinguished for its advanced welding capabilities. This engine-driven welder is designed to deliver consistent power and is equipped with a robust yet portable design. A key feature of the 1164-000-EA is its multiple welding processes, which include Stick, TIG, and MIG welding. This versatility makes it ideal for various applications, from heavy industrial work to smaller fabrication tasks. The machine is powered by a reliable diesel engine, providing excellent duty cycle and efficiency in diverse working conditions.

On the other hand, the Lincoln 1154-000-EA is known for its sophisticated control technologies. It features advanced inverter technology, which significantly reduces the machine's weight while enhancing its performance. This welder also provides precise control over the welding arc, resulting in smoother finishes and reduced spatter. With its user-friendly interface and digital displays, operators can easily customize settings to match specific project requirements. The 1154-000-EA is particularly favored in precision welding environments where both reliability and quality are paramount.

Lastly, the Lincoln 1155-000-EA continues this trend of excellence with its emphasis on efficiency and ease of use. This model leverages Lincoln's proprietary technologies to optimize the welding process while minimizing energy consumption. With an emphasis on portability and user convenience, it’s designed for those who require mobility without compromising performance. The intuitive controls combined with features like Hot Start and Auto-Lift Arc functionality further contribute to its ease of use, making it suitable for both novice and experienced welders.

All three models underscore Lincoln Electric's dedication to providing high-quality and dependable welding equipment. Each is built to meet the challenges of modern-day welding tasks and offers unique features that cater to a wide range of industrial needs. With robust construction, advanced welding technologies, and user-oriented designs, the Lincoln 1164-000-EA, 1154-000-EA, and 1155-000-EA exemplify the company's mission to equip welders with the tools necessary to excel in their work.
Top Page Image Contents