Lincoln 1154-000-EA, 1164-000-EA Phase, Refer to Proper Schematic for Identified Components

Page 12

 

 

should be approx. 25-100 Hz. If these readings are not

 

 

achieved, replace conveyor motor. If the readings are

 

 

achieved, proceed.

 

Oven control

If the hall effect sensor readings are correct, but there

 

 

is no speed indicated on the display, replace the oven

 

 

control

TROUBLESHOOTING GUIDE

IMPINGER II ADVANTAGE

SERIAL NUMBER 2038616 AND ABOVE (OVENS WITH PUSH BUTTON CONTROLS)

MODEL 1164-000-EA 400/230VAC

50HZ.

3 PHASE

REFER TO PROPER SCHEMATIC FOR IDENTIFIED COMPONENTS

 

 

 

 

SYMPTOM

POSSIBLE CAUSE

EVALUATION

 

Oven fan will not run

Incoming power supply

Check breaker, reset if required. Check power plug to

 

 

be sure it is firmly in receptacle. Measure incoming

 

 

power, call power co. if needed.

 

Oven cavity hi-limit

Terminals are normally closed, opens at 660°F (350°C).

 

thermostat

If open, reset and test oven for proper operation. If

 

 

thermostat will not hold for maximum oven temperature,

 

 

and oven is not exceeding control setting, check for

 

 

proper location of capillary bulb ion its spring holder. If

 

 

above checks are okay, replace hi-limit thermostat.

 

Fuse, 10 amp

Check, replace if necessary.

 

Fuse holder

Check, replace if necessary.

 

Hi-limit thermostat, control

Check for voltage on both sides of switch. Terminals are

 

box

normally closed. If open, reset and test oven for proper

 

 

operation. If thermostat will not hold, and control box

 

 

temperature is not exceeding 140°F (60°C), replace

 

 

thermostat.

 

 

Switch, main fan

With power off, check continuity between switch

 

 

terminals. Replace as needed.

 

Motor, main fan

Check for opens, shorts or grounds. With power off, turn

 

 

fan blade to check for locked rotor.

 

Capacitor

Check for shorts or grounds.

 

 

WARNING: Capacitor has a stored charge, discharge

 

 

before testing.

 

No control box cooling

Incoming power supply

Check breaker, reset if required. Check power plug to

 

 

be sure it is firmly in receptacle. Measure incoming

 

 

power, call power co. if needed.

 

Oven cavity hi-limit

Terminals are normally closed, opens at 660°F (350°C).

 

thermostat

If open, reset and test oven for proper operation. If

 

 

thermostat will not hold for maximum oven temperature,

 

 

and oven is not exceeding control setting, check for

 

 

proper location of capillary bulb in its spring holder. If

 

 

above checks are okay, replace hi-limit thermostat.

 

Fuse, 10 amp

Check, replace if necessary.

 

Fuse holder

Check, replace if necessary.

 

Hi-limit thermostat, control

Check for voltage on both sides of switch. Terminals are

 

box

normally closed. If open, reset and test oven for proper

 

 

operation. If thermostat will not hold, and control box

 

 

temperature is not exceeding 140°F (60°C), replace

 

 

thermostat.

 

 

Switch, main fan

With power off, check continuity between switch

12

Impinger II – Advantage Digital Service Manual - International

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Impinger Advantage Digital Series Phase NAT. GASLP GAS Power Supply Main FAN Circuit Heat Circuit Conveyor Control Schematic Diagram Serial Number 2045408 and Above Serial Number 2038616 and Above Schematic Diagram NAT. GAS Page Page Belt JAM Refer to Proper Schematic for Identified Components Page With Power on and Thermocouple Belt JAM MOTOR, Main FAN Replacement Capacitor ReplacementON/OFF Switch Replacement Impinger II Advantage SeriesFuse Holder Replacement THERMOSTAT, Control BOX HI-LIMIT ReplacementCooling FAN, Control BOX Replacement THERMOSTAT, Cooling FAN, ReplacementTRANSFORMER, Control Replacement Oven Control ReplacementThermocouple Replacement Thermocouple Measurement Temperature F MillivoltsPage Temperature Regulation Valve Replacement IGNITER/SENSOR Assembly ReplacementBypass Orifice Replacement Main Burner Orifice ReplacementCAPACITOR, Conveyor Drive Motor Replacement AIR Pressure Switch ReplacementBEARING, Conveyor Replacement Mercury Contactor ReplacementImpinger II Advantage General View Letter Part Number DescriptionPage Impinger II Advantage Control BOX 1154-000-EA, 1155-000-EAPage 1164-000-EA Page Oven Back Assembly Page Conveyor / Door

1155-000-EA, 1164-000-EA, 1154-000-EA specifications

Lincoln Electric is a renowned name in the welding and cutting industry, and its products, especially the Lincoln 1164-000-EA, 1154-000-EA, and 1155-000-EA, represent the company's commitment to innovation and performance.

The Lincoln 1164-000-EA is particularly distinguished for its advanced welding capabilities. This engine-driven welder is designed to deliver consistent power and is equipped with a robust yet portable design. A key feature of the 1164-000-EA is its multiple welding processes, which include Stick, TIG, and MIG welding. This versatility makes it ideal for various applications, from heavy industrial work to smaller fabrication tasks. The machine is powered by a reliable diesel engine, providing excellent duty cycle and efficiency in diverse working conditions.

On the other hand, the Lincoln 1154-000-EA is known for its sophisticated control technologies. It features advanced inverter technology, which significantly reduces the machine's weight while enhancing its performance. This welder also provides precise control over the welding arc, resulting in smoother finishes and reduced spatter. With its user-friendly interface and digital displays, operators can easily customize settings to match specific project requirements. The 1154-000-EA is particularly favored in precision welding environments where both reliability and quality are paramount.

Lastly, the Lincoln 1155-000-EA continues this trend of excellence with its emphasis on efficiency and ease of use. This model leverages Lincoln's proprietary technologies to optimize the welding process while minimizing energy consumption. With an emphasis on portability and user convenience, it’s designed for those who require mobility without compromising performance. The intuitive controls combined with features like Hot Start and Auto-Lift Arc functionality further contribute to its ease of use, making it suitable for both novice and experienced welders.

All three models underscore Lincoln Electric's dedication to providing high-quality and dependable welding equipment. Each is built to meet the challenges of modern-day welding tasks and offers unique features that cater to a wide range of industrial needs. With robust construction, advanced welding technologies, and user-oriented designs, the Lincoln 1164-000-EA, 1154-000-EA, and 1155-000-EA exemplify the company's mission to equip welders with the tools necessary to excel in their work.
Top Page Image Contents