Bunn CDS-3, CDS-2 service manual Dispense Solenoid Valve Location

Page 32

SERVICE (cont.)

DISPENSE SOLENOID VALVE

P1935

FIG. 31 DISPENSE SOLENOID VALVE Location:

The dispense solenoid valve is located on the left side of the dispenser base inside of the rear cover.

Test Procedures:

1.Disconnect the dispenser from the power source.

2.Disconnect the white/red and white/brown wires from the solenoid valve.

3.Check the voltage across the white/red and white/ brown wires with a voltmeter. Connect the dis- penser to the power source. The indication must be:

a)120 volts ac for 120 volt models.

b)230 volts ac for 230 volt CE models.

4.Disconnect the dispenser from the power source.

If voltage is present as described, proceed to #5.

If voltage is not present as described, refer to wiring diagrams and check the dispenser wiring harness.

5.Check for continuity across the solenoid valve coil terminals.

If continuity is present as described, reconnect the white/red and white/brown wires to the solenoid.

If continuity is not present as described, replace the solenoid valve.

6.Check the solenoid valve for coil action. Connect the dispenser to the power source. Press the dis- pense switch and listen carefully for a "clicking" sound as the magnet attracts.

7. Disconnect the dispenser from the power source.

If the sound is heard as described and water will not pass through the solenoid valve, there may be a block- age in the water line before the solenoid valve or, the solenoid valve may require inspection for wear and the removal of waterborne particles.

If the sound is not heard as described, replace the solenoid valve.

Removal and Replacement:

1.Disconnect the dispenser from the power source and the water supply.

2.Remove the six #8-32 screws securing the rear panel to the dispenser.

3.Remove the white/red and white/brown wires from the solenoid valve.

4.Disconnect the water lines to and from the solenoid valve.

5.Remove the two #8-32 nuts securing the solenoid mounting bracket to the dispenser base. Remove the solenoid and bracket assembly.

6.Remove the two #10-32 screws and lockwashers securing the solenoid valve to the bracket.

7.Install a new solenoid valve to the bracket using two #10-32 screws and lockwashers.

8.Install the solenoid and bracket to the base and secure with two #8-32 nuts.

9.Install the water lines to and from the solenoid valve using pipe thread sealant (BOM #M2526.0000) and tighten securely.

10.Refer to Fig. 32 when reconnecting the wires.

WHI/RED to Control

Board (J7-2)

WHI/BRN to Control

Board (J7-4)

P1909

FIG. 32 DISPENSE SOLENOID TERMINALS

32

29793 011500

 

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Post Office BOX SPRINGFIELD, Illinois Phone 217 529-6601 FAX 217Initial SET-UP BUNN-O-MATIC Commercial Product WarrantyIntroduction User Notices Operating Instructions Adjustments Cleaning Recommended Daily Cleaning and Maintenance TipsRemoving and cleaning the whipper chamber once a day Thorough cleaning of the hopper once a weekFault List Normal operation Powder Auto-Fill ready toDispense Door not closedTroubleshooting Problem Probable CauseTroubleshooting ProblemRemedy CDS product tastes watery or sugaryProblem Probable Cause Remedy Procedures. See Improper adjustment of productInstall a regulator if necessary to Product overflows CDS hopper Control Board and ProbeContents ServiceComponent Access Auger Drive Components Hopper LidRetainer Clip Spacer Dust Seal Hopper BaseDiagrams and check wiring harness Auger Drive MotorFrother and MIXING/WHIPPER Chamber Mixing ChamberWhipper Motor Volts ac for 120 volt models Volts ac for 230 volt CE modelsInstall dispense tip into the bottom of the whipper chamber Whipper MotorIf voltage is present as described, proceed to #9 Control Board and Level ProbeIf voltage is present as described, proceed to #5 Test Procedure Low Product Detect Instal the new control board using the four #6-32 keps nuts Remove the control boardLocation TEST/SERVICE SwitchDisconnect the wires from the switch terminals Main Power ON/OFF Switch Main Power ON/OFF SwitchLamp Cord Assembly Refer to when reconnecting the wiresRemove new nut and washer from new lamp cord connector Lamp Cord ConnectorDisconnect the lamp cord from the lamp cord connector Lamp HOLDER/SOCKET Assembly Close the dispenser doorTransformer TransformerPotentiometer PotentiometerHopper Level Indicator Hopper Level IndicatorHopper Switch Hopper SwitchDoor Switch Door SwitchAdjustments Pressure Regulator and Needle ValveDispense Solenoid Valve Dispense Solenoid Valve LocationWiring Diagrams Schematic Wiring Diagram PAFSchematic Wiring Diagram Pafa
Related manuals
Manual 60 pages 54.74 Kb Manual 34 pages 40.35 Kb

CDS-2, CDS-3 specifications

The Bunn CDS-3 is a commercial coffee brewer renowned for its reliability, efficiency, and high-quality performance. Designed for busy environments such as cafés, restaurants, and convenience stores, it offers the perfect balance of capacity and functionality, making it ideal for high-demand situations.

One of the standout features of the Bunn CDS-3 is its ability to brew up to 3.8 gallons of coffee per hour. This impressive capacity meets the needs of busy establishments where a constant supply of fresh coffee is crucial. The brewer’s stainless steel construction not only ensures durability but also maintains temperature, thus preserving the coffee’s rich flavor and aroma.

The CDS-3 incorporates Bunn's patented brewing technology, including the "Pour-Over" method. This feature allows for easy operation and contributes to the even extraction of coffee grounds. The machine is equipped with a pre-infusion mode that saturates coffee grounds before brewing, enhancing extraction for a fuller, more complex flavor profile.

Temperature control is another vital characteristic of the Bunn CDS-3. It maintains the water temperature between 195°F to 205°F, the ideal range for optimal coffee brewing. The brewer’s internals are designed for rapid heating, ensuring that the water reaches the desired temperature quickly and consistently, which is essential for high-quality coffee production.

In terms of usability, the Bunn CDS-3 offers an intuitive interface, allowing staff to operate it with minimal training. The front-access design not only simplifies maintenance, but also makes it easy to refill water and perform routine cleaning. Furthermore, the large capacity coffee pots ensure that the brewed coffee can be stored efficiently, minimizing waste.

Equipped with a unique spray head system, the Bunn CDS-3 ensures uniform saturation of the coffee grounds. This feature supports optimal extraction, allowing users to produce a rich and flavorful brew that keeps customers coming back for more.

In summary, the Bunn CDS-3 is a well-engineered, commercial-grade coffee brewer that excels in high-demand environments. Its robust construction, advanced brewing technology, consistent temperature control, and user-friendly design make it a favorite among coffee enthusiasts and professionals alike, affirming its reputation as a reliable and effective solution for coffee brewing needs. Whether for a bustling café or a catering service, the Bunn CDS-3 delivers a consistently great cup of coffee every time.
Top Page Image Contents