INITIAL SETUP
CAUTION: The brewer must be disconnected from the power source throughout the initial setup, except when
specified in the instructions. |
|
|
|
|
|
|
|
| |||
1. | Insert an empty funnel into the funnel rails of the brew |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||
| station. |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||
2. | Place an empty server under the funnel. |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||||
3. | Connect the brewer to the power source. Main ON/OFF |
|
|
|
|
|
|
|
|
| |
| Switch (located in bottom cover behind right front leg |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
| on some brewers) must be in the ON position. Water will | ° |
| ° | ° | ° | |||||
| begin flowing into the tank and stop when the tank is filled |
|
|
| |||||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
| to its capacity. Display will show PLEASE WAIT...TANK |
|
|
|
|
|
|
|
| ||
| FILLING until tank is filled with water. |
|
|
|
|
|
|
|
| ||
4. | Wait approximately twenty minutes for the water in the |
|
|
|
|
|
|
|
| ||
| tank to heat to the proper temperature. Display will show |
|
|
|
|
|
|
|
| ||
| READY TO BREW...WATER TEMP: XXX˚ when tank is at |
|
|
|
|
|
|
|
| ||
| operating temperature. |
|
|
|
|
|
|
|
| ||
NOTE: Brew water temperature is factory set at 200° F
(93.3° C). Refer to TEMPERATURE SELECTION below
should the water temperature need to be increased or decreased. When brew water temperature is changed, ready temperature should be increased or decreased ac- cordingly. 5. Place a small vessel beneath the faucet and open the faucet handle. Release it when you hear the tank refilling.
6. Water volumes have been preset at the factory. Refer to adjustments for the Set Brew Volumes section of the Programming Manual on the
www.bunn.com should the volume need to be increased or decreased.
7. The brewer is now ready for use in accordance with the coffee brewing instructions.
TEMPERATURE SELECTION
SET TEMP - Range: 185˚F (85˚C) to 205˚F (96˚C)
This function allows the operator to set the brew water temperature in the tank. It also sets the hot water faucet dispense temperature.
SET TEMP: XXX° (-) DONE (+)
Procedure to set brew temperature:
1.Press and hold upper right hidden switch until the display reads SELECT RECIPE. Release switch. Continue to press and release switch until the display reads SET TEMP.
2.To adjust the brew temperature, press
3.When finished, press and release DONE to save the new setting, exit the SET TEMP function and advance to the next function screen, SET READY. Another alternative is to press and release the ON/OFF switch (either on DUAL brewers) located on the front switch panel to exit the SET TEMP function and return to the MAIN
SCREEN.
Page 7 | 34025.4 031312 |
|