Bunn Comprehensive Guide to Coffee Maker Water Adjustment for Optimal Brewing

Page 6

INITIAL SET-UP (cont.)

29.If not, unplug the brewer and remove the top lid.

30.Adjust the delay knob of the timer on the right side of the hood as required. Replace the top lid and plug in the brewer.

31.Repeat steps 27-30 until the proper dilution timing is achieved.

ADJUSTING BREW VOLUMES

CAUTION - Disconnect the power source from the brewer prior to the removal of any panel for the replacement or adjustment of any component.

NOTE: Prior to setting or modifying batch sizes, check that the brewer is connected to water supply, the tank is properly filled, and a funnel and server are in place.

1.Modifying batch sizes. To modify a batch volume, first check that the SET/LOCK switch is in the "SET" position on the circuit board.

To increase a batch size. Press and hold the START or BREW switch until three clicks are heard. Release the switch (Failure to release the switch within two seconds after the third click causes the volume setting to be aborted and previous volume setting will remain in memory) and press it again one or more times. Each time the switch is pressed, two seconds are added to the brew time period. Allow the brew cycle to finish in order to verify that the desired volume has been achieved.

To decrease a batch size. Press and release the START or BREW switch once for every two-second interval to be removed from the total brew time period; then immediately press and hold down the START or BREW switch until three clicks are heard. Release the switch. (Failure to release the switch within two seconds after the third click causes the volume setting to be aborted and previous volume setting will remain in memory). Allow the brew cycle to finish in order to verify that the desired volume has been achieved.

2.Setting batch sizes. To set a batch volume, first check that the SET/LOCK switch is in the "SET" position on the circuit board. Press and hold the START or BREW switch until three distinct clicks are heard, and then release the switch. (Failure to release the switch within two seconds after the third click causes the volume setting to be aborted and previous volume setting will remain in memory). View the level of the liquid being

dispensed. When the desired level is reached, turn the ON/OFF switch to "OFF" (lower). The brewer remem- bers this volume and will continue to brew batches of this size until the volume setting procedure is repeated.

NOTE: When brewing tea, batch volumes will decrease due to absorption by the tea grounds.

3.Setting programming disable feature. If it becomes necessary to prevent anyone from changing brew times once programmed, you can set the SET/LOCK switch to the "LOCK" position. This will prevent any program- ming to be done until switch is once again placed in the "SET" position.

AUTO SWEETENER SET-UP

CAUTION - The brewer must be disconnected from the power source throughout the Initial Set-Up, except when specified in the instructions.

1.Remove the top lid and both rear panels.

2.Make sure the brewer water supply is off.

3.Connect sweetener hose from the bag in a box delivery system to the rear fitting marked "Sweetener" . IMPORTANT - System delivery pressure must be regulated between 30-40 psi. System also needs to deliver product for at least 4 minutes without shutting off. Some pump systems shut off after a few minutes of continu- ous running.

4.Set the "Delay knob on the dilution timer to the 3 minute setting. (The minimum delay setting)

Page 6

10225

031804

 

 

Image 6
Contents TU3 Phone 217 529-6601 FAX 217Contents BUNN-O-MATIC Commercial Product WarrantyIntroduction User Notices #00831.0000 #00656.0000#03408.0002 #03409.0002 #03408.0000 #03409.0000 Electrical Requirements Plumbing RequirementsElectrical Hook-Up Initial SET-UP StoppedAdjusting Brew Volumes Auto Sweetener SET-UPInitial SET-UP Cleaning Operating ControlsAuto Sweetener Cleaning CleaningTEA Brewing Troubleshooting Problem Probable CauseRemedy Troubleshooting ProblemRemedy Problem Probable Cause Remedy Dilution cycle will not start Dilution Solenoid ValveFunnel Tip Spitting or excessive steamingDrip-out time too long Control Thermostat Ticles clogging the drip-out tipBeverage overflows dispenser Dispenser See Dilution TimerIng Water Temperature Dilution Solenoid ValveRemove and clean lime off the tank heater. See Dry tea leaves remain in the funnelService Component AccessContents Service Brew Solenoid ValveSolenoid valve Service Brew Timer Early Models Brew TimerService Digital Brew Timer Late Models If voltage is as described, proceed to #7Digital Timer Wiring Control Thermostat Dilution Solenoid Valve Dilution Solenoid ValveDilution Timer Limit Thermostat Indication must beIng Diagrams and check the wiring harness ON/OFF SwitchON/OFF Switch Selector Switch Optionalcont Start Switch Start SwitchSweetener Solenoid Valve Optional Tank Heater 10225 071500 10225 071500 Single Phase Volts AC10225 071500
Related manuals
Manual 2 pages 32.73 Kb

TU3 specifications

The Bunn TU3 is a renowned commercial coffee brewer known for its reliability and performance in bustling coffee shops, restaurants, and diners. Designed to cater to high-demand environments, the TU3 stands out with a variety of features that ensure an optimal brewing experience.

One of the primary characteristics of the Bunn TU3 is its capability to brew large volumes of coffee efficiently. It has a 3-gallon capacity, making it ideal for establishments that serve numerous customers throughout the day. This model can produce up to 19 gallons of coffee per hour, allowing establishments to keep pace with customer demand without sacrificing quality or flavor.

At the heart of the Bunn TU3's performance are its advanced brewing technologies. The brewer features a patented "multi-stream" spray head that evenly distributes hot water over coffee grounds, ensuring optimal extraction for a richer taste. This technology contributes to the consistent flavor profile that customers expect in a quality cup of coffee.

The TU3 is also equipped with a built-in hot water faucet, providing added convenience for brewing tea or instant beverages. Operators can easily access boiling water without interfering with the brewing process, streamlining service during peak hours. The adjustable temperature settings further enhance control over the brewing process, allowing for customization based on the coffee type or personal preference.

In terms of construction, the Bunn TU3 is built to withstand the rigors of commercial use. The brewer boasts a durable stainless steel body that is not only stylish but also easy to clean, helping maintain a professional appearance in any setting. Additionally, the brewer's design incorporates features such as a splash guard and easy-to-use controls, making it user-friendly for staff members.

Energy efficiency is another highlight of the Bunn TU3. Its innovative design helps in reducing energy consumption while still providing rapid brewing capabilities. This feature is particularly appealing to environmentally conscious operators looking to minimize their operational impact.

Overall, the Bunn TU3 coffee brewer combines speed, reliability, and exceptional brewing technology, making it a top choice for businesses that prioritize quality coffee service. Its combination of durability, efficiency, and user-friendly features ensures that it can handle the demands of any high-volume coffee operation, delivering excellent results cup after cup.