Bunn AFPO-3, AFPO-2 SL service manual Fuse and Fuse Holder, Location

Page 11

SERVICE

FUSE AND FUSE HOLDER

 

 

 

 

 

1

 

 

 

 

REFILL

2

 

 

 

 

 

 

 

 

3

 

MAIN

 

 

 

 

 

POWER

 

 

 

WATER

 

 

 

 

 

INPUT

 

 

 

 

1

1

 

 

 

 

FLAVOR

FLAVOR

 

 

 

 

INPUT

 

 

 

 

OUTPUT

2

 

 

 

2

WATER

3

 

 

 

 

OUTPUT

 

 

 

FLAVOR

 

 

 

 

 

OUTPUT

 

 

 

 

3

WATER

 

 

 

 

 

OUTPUT

 

 

 

 

FLAVOR

 

 

 

 

 

OUTPUT

 

 

 

 

 

WATER

 

 

 

 

 

OUTPUT

 

 

 

 

 

FIG. 4 FUSE HOLDER

 

P1516

 

 

Location:

The fuse holder is located on the lower right front of the autofill box just to the left of the power cord.

Test Procedure:

1.Disconnect the dispenser from the power source.

2.Remove cap and fuse from fuse holder.

3.Remove fuse from the cap.

4.Check for continuity through the fuse.

If continuity is present, reinstall the fuse, the fuse is operating properly.

If continuity is not present, replace the fuse.

Removal and Replacement:

Fuse:

1.Remove the cap from the fuse holder.

2.Remove fuse from the fuse holder and inspect. If blown, discard.

3.Install new 10 amp fuse in the fuse holder.

4.Reinstall fuse holder cap.

Fuse Holder:

1.Disconnect the dispenser from the power source.

2.Disconnect the wires from the rear of the fuse holder.

3.Remove the nut securing the fuse holder to the front of the main mounting panel.

4.Push the fuse holder through the hole in the panel.

5.Install new fuse holder and fuse through the hole in the panel.

6.Secure the fuse holder to the panel.

7.Refer to Fig. 5 and reconnect the wires.

BLK from Main

Wiring Harness

BLK to Main

ON/OFF Switch

 

P1331

FIG. 5 FUSE HOLDER TERMINALS

 

11

28791 040501

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Phone 217 529-6601 FAX 217 Post Office BOX SPRINGFIELD, IllinoisUser Notices WarrantyIntroduction Initial SET-UP Electrical RequirementsElectrical Hook-Up Plumbing RequirementsInitial SET-UP Cleaning Recommended Weekly CleaningMIX Ratio Adjustments Time for Flavor Output 1/2 cup Time for Water Output 1 cup MIX Ratio ADJUSTMENTScontProbe Control BOX LOW/OFF/HIGH Main Power ON/OFFRefill Circuit ON/OFF TEST/OPERATEProblem Probable Cause Remedy TroubleshootingTroubleshooting Contents Component AccessCircuit Board Circuit Board Connector LocationLocation Fuse and Fuse HolderMain ON/OFF Switch ServiceMoving Probe System#3 AFPO-3 only Pump Flavor ON/OFF Switches#1 AFPO-2 #2 AFPO-2Refill Switches Refill SwitchesOnly #2 AFPO-2 #3 AFPO-3Solenoid Water ON/OFF Switches Solenoid Water ON/OFF SwitchesTEST/OPERATE Switch Terminals Pump Motor Removal and Replacement VACUUM/SUPPLY Pump AssemblyTubing Start Position VACUUM/SUPPLY Pump Tube InstallationVacuum Switches Vacuum SwitchesPiping Diagram AFPO-2 Schematic Wiring Diagram AFPO-2 Schematic Wiring Diagram AFPO-3 Schematic Wiring Diagram AFPOA-2
Related manuals
Manual 25 pages 230 b Manual 8 pages 54.73 Kb

AFPO-2, AFPO-2 SL, AFPO-3 specifications

The Bunn AFPO-2 SL, AFPO-3 SL, and AFPO-3 are advanced coffee brewing systems that cater to the needs of commercial establishments seeking efficiency and high-quality coffee production. These machines are designed for ease of use, high throughput, and flexibility, making them ideal for coffee shops, restaurants, and workplaces.

The Bunn AFPO-2 SL is known for its dual-brew capabilities, allowing users to brew coffee and tea simultaneously. This model features a sleek, stainless-steel design that fits well in various settings. It comes equipped with an electronic controls interface that ensures precise brewing temperatures and times, enabling baristas to consistently produce flavorful coffee. The AFPO-2 SL has a brewing capacity of up to 3.8 gallons per hour, making it suitable for high-demand environments.

Another standout model is the Bunn AFPO-3 SL, which builds upon the features of the AFPO-2 SL with an increased brewing capacity of up to 4.5 gallons per hour. This model includes a programmable digital control module, which allows users to customize brew cycles for different coffee blends, enhancing versatility. The AFPO-3 SL is designed with stainless-steel construction, ensuring durability and longevity while maintaining easy cleaning and maintenance routines.

The hallmark of the Bunn AFPO-3 is its single-serve capability, which provides a fresh-brewed experience for every cup. With advanced technology that ensures optimal water temperature and flow rate, the AFPO-3 guarantees rich and robust flavors in every pour. This model is ideal for establishments that want to offer their customers a variety of coffee options without sacrificing quality or speed. It also features an intuitive user interface, allowing staff to operate the machine with minimal training.

All three models are equipped with a built-in hot water tap, providing instant access to hot water for tea or other beverages, further increasing their utility in busy environments. The Bunn AFPO series is known for its reliability, with heavy-duty components that withstand the rigors of daily use.

In summary, the Bunn AFPO-2 SL, AFPO-3 SL, and AFPO-3 represent the pinnacle of brewing technology in the commercial coffee market. With their advanced brewing capabilities, user-friendly designs, and robust construction, these machines are perfectly suited for any establishment that values quality coffee and operational efficiency.
Top Page Image Contents