XTRA Full Rack Series • Setup Guide, cont’d
WARNING: Do not short the “+” and “_” outputs to each other. Doing so will short the |
outputs and may damage the amplifier. |
For complete wiring details, see “Rear Panel Features and Operation” in the user guide.
5.Bridge outputs (XPA 2002, XPA 2004) — Bridging the output of input 1 (for the XPA 2002) or inputs 1 and 3 (for the XPA 2004) doubles the output of those inputs. See
“Bridged mode output” in the user guide for further details.
Bridge mode: XPA 2002
Bridging takes the signal from input 1 and outputs the combined output of 400 watts from the + terminals of output channels 1 and 2. Toggle the bridged output mode switch up (bridged) or down (unbridged). See the diagram at right.
Bridge mode: XPA 2004
Bridging takes the signal from input 1 or input 3 or both and outputs the combined output of 400 watts from the
+terminals of output channels 1 and 2 (Bridge A), or output channels 3 and 4 (Bridge B), or both. Toggle the bridged output mode switch up (bridged) or down (unbridged) for the appropriate input channel. See the diagram at right.
BRIDGE |
| BRIDGE A | |
MODE |
|
|
|
A |
| 1 | 2 |
ON |
|
|
|
OFF | 8 | / 4 | (BRIDGE 8 ONLY) |
|
8 Ohm
NOTE: When bridging outputs, the minimum load impedance is 8 ohms.
6.Reconnect all power cords and switch on all other equipment before powering up the power amplifier. The amplifier must be powered up last. The front panel LED of the amplifier should light green.
7.Adjust the audio level using the rear panel adjustment screws, shown at right.
| 1 |
|
| 2 |
|
| 3 |
|
| 4 |
|
12 | 10 | 8 | 12 | 10 | 8 | 12 | 10 | 8 | 12 | 10 | 8 |
14 |
| 614 |
|
| 6 14 |
|
| 6 14 |
|
| 6 |
18 |
| 4 |
|
| 4 |
|
| 4 |
|
| 4 |
8. Set the high pass filter — Use a small | 26 | 2 | 2 |
screwdriver to toggle this switch between off |
| 0 | 0 |
(no filtering) and 80 Hz. The XPA
XPA
9. If desired, wire a contact closure device to the remote standby connector. Connecting pin 2 to ground (pin 1) places the amplifier in standby mode. Standby mode
turns off all outputs, although the amplifier is still receiving power.
Use the included
2 2
00
HPF
CH 3 80 Hz
OFF
XPA 2003C-70V
To Contact Closure Port on Control Device
STANDBY
Extron USA - West | Extron USA - East | Extron Europe | Extron Asia | Extron Japan | Extron China | Extron Middle East |
Headquarters |
|
|
|
|
|
|
+800.633.9876 | +800.633.9876 | +800.3987.6673 | +800.7339.8766 | +81.3.3511.7655 | +400.833.1568 | +971.4.2991800 |
Inside USA/Canada Only | Inside USA/Canada Only | Inside Europe Only | Inside Asia Only | +81.3.3511.7656 FAX | Inside China Only | +971.4.2991880 FAX |
+1.714.491.1500 | +1.919.863.1794 | +31.33.453.4040 | +65.6383.4400 |
| +86.21.3760.1568 |
|
+1.714.491.1517 FAX | +1.919.863.1797 FAX | +31.33.453.4050 FAX | +65.6383.4664 FAX |
| +86.21.3760.1566 FAX |
|
|
|
| ||||
| © 2010 Extron Electronics. All rights reserved. www.extron.com |
10 10