Extron electronic P/2 DA2 D Installing the P/2 DA2 WM F/EC F Easy setup procedure, Medium

Page 9

Controls and Installation, cont’d

3Gain switch — To compensate for cable resistance and capacitance, use a small screwdriver to slide this switch to select the level of video gain that yields the sharpest, smear-free picture.

Normal –

Unity gain

Medium –

1 2 3 4

ON

AUDIO OUTPUT LR 1 2 34

SW 4= Sp are

OFF= 10 kOhm

ON= 510 Ohm,

SW 3= SYNC Inpu t aImpednce

P/2 DA2 D CONFIG Switches SW 1= Loc al Monitor ON= Present, OFF= NotPresent SW 2= A udio Ou pu tConfig ON=Stereo, OFF= D ua lMONO

Mid-level

 

 

 

CONFIG

 

 

 

 

 

peaking

 

 

 

 

 

 

 

 

 

and gain

 

 

 

 

 

 

 

 

 

 

3

 

NORM

 

 

OUTPUT

VIDEO

 

 

 

 

 

HIGH

GAIN

VIDEO

 

 

 

 

Max. peaking

 

 

MED

POWER 12V

N15779

Anaheim,CA

ExtronElectronics

33 -1663-01A05

 

 

0.2AMAX

High –

 

 

 

 

 

 

 

 

 

& gain

 

 

 

 

 

 

 

 

08

P/2 DA2 D (viewed from rear)

NAdjust the gain before installing the P/2 DA2 D

into a wall, as the gain switch will be inaccessible after installation.

4Power input — Connect the included 12 VDC external power supply into the 2-pole, 3.5 mm captive screw connector. Be careful to observe the correct polarity.

Smooth

Ridges

A

A

Power Supply

Output Cord

SECTION A–A

5Video output — BNC connectors for RGBHV output.

Installing the P/2 DA2 WM F/EC F

Easy setup procedure

The wall-mounted P/2 DA2 WM F kit consists of the faceplate/ distribution amplifier assembly and a mounting bracket that mounts in a wall opening and to which the faceplate assembly is attached. The P/2 DA2 WM EC F kit consists of the faceplate/ distribution amplifier assembly that mounts in the Euro Channel raceway.

1For wall mounting only: Using the mounting template provided in the appendix as a guide, carefully cut a mounting hole through the wall where the mounting bracket is to be installed.

2For wall mounting only: Install the mud ring mounting bracket using the supplied screws and mounting clips. Refer to the section “Installing a mud ring bracket” for further details.

3Before connecting any cables, power off all equipment. If the optional architectural adapter plate (AAP) is being installed, please refer to “Installing architectural adapter plates” in this chapter.

4The rear connectors are the same for both WM F and WM F EC models. Connect the VGA output cable to the 15-pin HD female output connector. To prevent installation debris or objects from entering the opening in the sheet metal just above this VGA connector, use masking tape to temporarily cover this opening. Remove this tape after installation is completed. Next, if there is audio output, connect the audio output cable to the captive screw connector. Finally, connect the power cable to the power input connector. Refer to the “Cabling” and “Connecting audio” sections of this chapter.

5Before attaching the faceplate assembly to the wall mounting bracket/Euro Channel, attach the computer video cable to the 15-pin HD female input connector on the faceplate. Next, a local monitor may be connected to the 15-pin HD female buffered local monitor output connector on the faceplate. Finally, for audio input, connect the audio cable to the faceplate’s 3.5 mm audio input jack. Refer to the “Cabling” and “Connecting audio” sections of this chapter. For Euro Channel applications, refer to the “Euro Channel installation” section.

2-6

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

2-7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Distribution Amplifiers DA2 WM F, WM EC F DA2 D, and AAP modelsPrecautions DA2 WM Series, EC, & D Controls and Installation Table of Contents One Table of Contents, cont’dAbout the P/2 DA2 WM F/EC F, AAP, and D Models FeaturesDA2 WM EC F faceplate features DA2 WM F faceplate featuresDA2 D faceplate features Front and Rear PanelsControls and Installation, cont’d DA2 WM F/EC F rear connectorsDA2 WM F/EC F rear panel DA2 D rear panel Medium Installing the P/2 DA2 WM F/EC F Easy setup procedureInstalling a mud ring bracket Installing the mud ring bracketCabling Connecting audio outputDA2 WM F cabling Fastening captive screwsInstalling adapter plates Installing architectural adapter platesDA2 WM EC F Euro Channel installation DA2 WM F wall mount installationSetting the DIP switches Euro Channel installationSetting the internal jumpers Installing the P/2 DA2 DPreparing the site and installing the wall box Setting the internal jumpersMounting the distribution amplifier Attaching the wall box to a wall studMounting the distribution amplifier to the wall box DA2 D application example Replacing the faceplateVideo SpecificationsVideo input Video outputAudio Specifications, Dimensions, Parts, cont’dAudio input Audio outputDimensions Specifications, Dimensions, and Parts, cont’dDA2 WM F faceplate dimensions WM F model faceplate dimensionsModel faceplate dimensions WM F AAP model faceplate dimensionsCables Included PartsMud ring mounting brackets Optional architectural adapter platesSingle Type Connector Architectural Adapter Plates DA2 WM F DA2 D mounting template DA2 WM F AAP mounting template18 P/2 DA2 WM/EC/D/AAP Series Appendix

WM EC F, P/2 DA2 WM EC F, P/2 DA2 D, P/2 DA2 EC F specifications

Extron Electronics is a renowned manufacturer of advanced audiovisual (AV) solutions, providing high-quality distribution and control systems for various environments. Among their extensive product range, the P/2 DA2 EC F, P/2 DA2 WM EC F, WM EC F, and P/2 DA2 D models stand out for their exceptional performance and innovative technologies.

The P/2 DA2 EC F is a premium video distribution amplifier designed for balancing and distributing high-resolution video signals. One of its main features includes support for resolutions of up to 1080p, ensuring sharp and clear image quality over long distances. The unit incorporates Extron's proprietary technologies, such as Extron's Brightness and Contrast Enhancement, which help to optimize picture quality by improving brightness levels, contrast ratios, and overall color fidelity. Additionally, the P/2 DA2 EC F offers a user-friendly design, with easy-to-use front panel controls and a compact form factor that simplifies installation in various AV setups.

Similarly, the P/2 DA2 WM EC F is a wall-mountable version of the video distribution amplifier, catering to installations where space is limited. This feature enables efficient use of wall space without compromising on performance. Like its counterpart, it supports high-definition video signals and ensures the integrity of audio-visual content, making it a reliable choice for classrooms, conference rooms, and other professional settings.

The WM EC F model, designed specifically for ease of integration within wall-mounted applications, further emphasizes user convenience through its lightweight design and compact nature. It is compatible with various mounting systems and provides convenient access for maintenance, making it suitable for environments with heavy AV usage.

On the other hand, the P/2 DA2 D is a distinct product that features dual output capabilities, making it ideal for distributing video signals to two separate display devices simultaneously. With high bandwidth and excellent signal integrity, it ensures a seamless experience across multiple displays. The robust design accommodates various installation environments, including video conferencing, digital signage, and more, without any loss in resolution or quality.

Overall, Extron's P/2 series, including the DA2 EC F, DA2 WM EC F, WM EC F, and DA2 D, showcases advanced engineering in video distribution technology, offering versatile solutions tailored to meet the needs of modern AV installations. With their high performance, rich features, and user-centric design, these products continue to be essential tools for professionals in the audiovisual field.
Top Page Image Contents