-It is important to try and run the dishwasher when it is fully loaded in order to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle.
-Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are.
-Use the right amount of detergent: if you use too much deter- gent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment.
-There is no advantage in rinsing dishes, cookware and utensils before placing them in the dishwasher.
It may occur that the dishwasher does not function or does not function properly. Before calling for assistance, Iet us see what can be done first: have you forgotten to press one of the buttons or to perform an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
Error Messages
The dishwasher is equipped with a safety system that is able to detect operating problems and malfunctions. These malfunctions are signalled by the rapid blinking of one of the program LEDs. Only in the case where the indicator light for the soak cycle (see table for cycles) blinks rapidly should you cancel the cycle as described in the section entitled, "Changing a Cycle while Under- way." Then check to make sure that there is water in the mains
After Every Wash
After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside.
Remove the plug
Before cleaning or performing maintenance, always remove the plug from the socket. Do not run risks.
No solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Rather, use only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior, use a cloth dampened with water and white vinegar, or cleaning prod- uct made specifically for dishwashers.
When You Go on Holiday
When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly ajar. This will help the seals last longer and prevent odors from forming within the appliance.
Moving the Appliance
If the appliance must be moved, try to keep it in a vertical position. If absolutely necessary, it can be positioned on its back.
Seals
One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring.
- the door is closed properly; |
- the ON-OFF switch is on "ON"; |
- the water supply is turned on. |
The Dishwasher Does Not Load Water
Have you checked whether:
-the water is turned on and the hose is connected properly;
-the water supply to the house is on and has sufficient pressure;
-the water supply hose is crimped or bent;
-the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you checked whether:
If any of the other indicator lights begins to blink rapidly, turn off the appliance and call for technical assistance, indicating which light began to blink.
If, despite all these checks, the dishwasher still does not function and/or the problem persists, contact the nearest authorised ser- vice centre and provide them with the following information:
-the nature of the problem;
-the model type number (Mod...) And the
serial number (S/N...), which are indicated on the plate located on the side of the inner part of the door.
Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts.
Cleaning and Special Maintenance
Filter Assembly
For best performance and results, the filter assembly must be cleaned frequently.
The filter efficiently removes food residue from the wash water, allowing it to be recirculated during the cycle. For this reason, it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the "A" semi-circular filter and cup under running water. To remove the filter assembly, pull on the cup handle in the upward direction. The entire filter as- sembly (made up of the "A" semicircular filter and the "B" fine filter) should be cleaned at least once a week.
To clean the filter and the fine filter, use a cleaning brush. Then, reassemble the filter parts as shown in the figures below and reinsert the entire assembly in the dishwasher, positioning in its seat and pressing downward.
The dishwasher must never be used without the filters. Improper replacement of the filters may re- duce level of the appliance and damage dishes and utensils.
Cleaning the Spray Arms
It may happen that food particle become encrusted on the spray arms and block the holes. Check the spray arms periodically and clean them when needed.
A
B
Cleaning the Water Inlet Filter
Periodically clean the water inlet filter (see figure) located on the outlet of the water supply tap.
After turning off the water tap, unscrew the end of the water sup- ply hose, remove the filter and clean it carefully under running water. Then, return the filter to its place and tighten the water supply hose back into position.
-the water is turned on and the hose is connected properly;
-the water supply to the house is on and has sufficient pressure;
-the water supply hose is crimped or bent;
-the filter for the water supply hose is clogged.
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
-the lid to the salt container is closed properly;
-the rinse aid dosage is correct.
