Grindmaster G & MG Series instruction manual Connection To Main Power Supply, Figure F

Page 3

Installation (cont.)

4.) Installing the Top Lid Merchandiser (requires Phillips head screwdriver)

•Unplug the cord to the lid and remove the lid from the machine.

•On top of the cover, remove the 4 hole plugs over the front (2) screws, middle (near rocker switch) and back screws then remove these 4 screws with a Phillips head screwdriver. Remove the black top part of the cover from the clear plastic base. (see fig. E)

•Slide the merchandiser header around the outside edge of the lid’s clear plastic base. Position bottom edge of header in grooved area. (see fig. F)

•Reassemble the black top cover onto the clear plastic base. The top edge of header should slide into black top cover grooved area. (see fig. F) Replace screws. Replace hole plugs (the angled plugs goes in the rear hole, and the two large plugs go in the two front holes and the small plug goes in the center hole by the rocker switches).

•Replace assembled lid on machine and reattach cord.

5.Installing the Rear Back-lit Merchandiser

•To remove any existing artwork, bend or pinch the middle of the back-lit merchandiser and pull it from the rear merchandising display casing. (see fig. G)

•To insert new art, slide the left corner edges into the left top and bottom casing edges. (see fig. H)

•Slightly bend art and insert the right side of art into the right top and bottom casing edges. (see fig. H)

•Smooth out art until all edges are properly inserted into the casing.

(Figure E)

(Figure F)

(Figure G)

(Figure H)

Connection To Main Power Supply

!Attention: Before inserting the plug into the electrical outlet, carefully read the following precautions.

•The electrical safety of this Granita machine can only be achieved if the machine is properly connected to an appropriate grounded, electrical receptacle that is in compliance with current national safety stan- dards. Therefore, the manufacturer cannot be held responsible for damage and/or injury caused by fail- ure to connect the unit to an appropriate source of power.

•For a safe and correct installation, connect the unit to a dedicated outlet.

•Do not alter the cord or plug in any way.

!Attention: Altering the cord or plug will void the warranty.

•The entire length of the power supply cord must not, in any way, be compressed (bent or bunched together) nor may extension cords be used.

•Do not obstruct the ventilation and heat dispersion grill vents on the side and rear panels of the unit. An insufficient ventilation process may reduce the efficiency of the machine, causing it to function inade- quately, and cause serious damage to the machine. A minimum of eight inches (20cm) clearance is necessary on each side and behind the unit.

G & MG Series Granita Machine

Page 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Crathco Visual Granita Machine Introduction and Warnings Instructions For Machine Transport InstallationFigure F Connection To Main Power SupplyProgramming G Series Electronic Touchpad Models Preparing ProductOperating Panel Operating Panel -Electronic TouchpadModel G23-2B Electronic Touchpad Setting Defrost Timer Night SettingOperate in Manual Mode without Defrost Timer Activated Operate in Automatic Mode with Defrost Timer ActivatedTo obtain cold night/defrost drinks Stand-by mode settingDefrost Timer Operating Instructions To obtain a slushAdjustments Consistency AdjustmentDispensing Product Daily Cleaning Cleaning and Sanitizing ProceduresRectly positioned Cleaning and Sanitizing Procedures con’tRemoving and cleaning the filter Weekly MaintenanceLid Lights Maintenance con’tCleaning the Condenser Monthly Replacing the Lightbulbs As NeededTo Replace Spindle Bushing Seal Maintenance Bell Shaped SealRing Maintenance Spindle Bushing SealChecklist for Kit Serial # 11259 and above Crathco Granita Preventive Maintenance PMStainless shaft system, then use kit #90566 Maintenance PMCrathco Granita Preventive If unit has been converted to unhardenedAccessories not included Security Kit InstallationAutofills Problem Possible Cause Solution Troubleshooting GuideDispensing valve Troubleshooting Guide cont’dFor units up to serial number Exploded View MG23-2B 115/60Exploded View G23-2B 115/60 Serial number 8195 and higher Exploded View MG23-2B 115/60 Exploded View G235-2B 220/50 Exploded View MG235-2B 220/50 Exploded View G236-2B 220/60 Exploded View MG236-2B 220/60 Part Description Crathco Granita G & MG Series Parts ListGear Motor Exploded View Refrigeration Diagram Model G Series 115V/220V Refrigeration Diagram Model MG Series Electrical Diagram Model MG Series Electrical Diagram Model MG Series Electrical Diagram Model G Series 115V/220V Page

G & MG Series specifications

Grindmaster G & MG Series showcases a remarkable innovation in the world of coffee grinding technology, blending efficiency, durability, and performance to meet the needs of coffee enthusiasts and professionals alike. These grinders are designed to deliver a superior grinding experience, ensuring that every bean is ground to perfection.

One of the standout features of the Grindmaster G & MG Series is its grinding consistency. Utilizing advanced burr grinding technology, these machines maintain an even grind size, essential for achieving the ideal flavor extraction in every brew. The series includes both flat and conical burr options, allowing users to select the type that best matches their brewing method. This versatility is critical for accommodating a range of coffee styles, from espresso to French press.

Another key characteristic of the G & MG Series is its user-friendly interface. Featuring intuitive controls and clear display options, operators can easily adjust grind settings to achieve their desired consistency. The timers and dosing controls enable precise measurements, ensuring that every cup is brewed with the exact amount of coffee needed for optimal taste.

Durability is a hallmark of the Grindmaster brand, and this series is no exception. Built with robust materials, the G & MG Series is designed to withstand the demands of high-volume coffee environments, such as cafes and restaurants. The components are engineered for longevity, minimizing maintenance downtime and ensuring that the grinder remains a reliable tool in any setting.

Furthermore, the Grindmaster G & MG Series integrates innovative technologies to enhance user experience. The models are equipped with noise-reducing features, making them suitable for environments where quiet operation is essential. Additionally, some models in the series offer advanced thermal stability technology, which helps maintain consistent performance without overheating.

In terms of design, the G & MG Series showcases a sleek, modern aesthetic that fits seamlessly into any café or kitchen decor. The grinders are available in various colors and finishes, allowing business owners to choose a look that aligns with their brand identity.

In conclusion, the Grindmaster G & MG Series stands out as a top choice for coffee grinding, combining advanced technology, user-friendly features, and robust construction. Whether for home use or commercial applications, these grinders provide an exceptional grinding experience, ultimately elevating the quality of coffee served.
Top Page Image Contents