Grindmaster 3342, 3352, 3341A manual Installation, Shipment Transit, Installing your Freezer

Page 7

INSTALLATION

Shipment Transit

The freezer has been operated and tested at the factory. Upon arrival the complete freezer must be thoroughly checked for any damage which may have occurred in transit. NOTE: A Tip (N) Tell warning device is placed on each shipping carton at the factory. If the arrow tip is blue, the carton has been tipped in transit. (see Figure B)

THE CARRIER IS RESPONSIBLE FOR ALL DAMAGE IN TRANSIT WHETHER VISIBLE OR CONCEALED. DO NOT PAY THE FREIGHT BILL until the freezer has been checked for damage. Have the carrier note any visible damage on the freight bill. If concealed damage and/or shortage is found later, advise the carrier within 10 days and request inspection. The customer must place any claim for damage and/or shortage with the carrier. Grindmaster Corporation cannot make any claims against the carrier.

Installing your Freezer

Figure B

1.Place the self-sealing rubber pad on a level counter stable and strong enough to support the freezer’s weight. If equipped with legs instead of pad, install legs by screwing them into the four leg holes on the bottom of the unit.

2.Make sure freezer is to be placed in a location that is within 6' of a properly grounded circuit and allows adequate space for rear remote refrigeration connections and on the sides for air circulation.

NOTE: Minimum clearance is 2" (5cm) on both sides and 8" (20cm) above the freezer. (see Figure C)

3. Remove the side panels with a Phillips screwdriver and supporting all four sides, lift

machine up and place in appropriate area.

Figure C

 

￿CAUTION: IF EQUIPPED WITH SPINNER DO NOT LIFT UNIT BY SPINNER SHAFT TO AVOID SERIOUS DAMAGE TO SPINNER.

￿CAUTION: BEVERAGE FREEZERS ARE HEAVY PIECES OF EQUIPMENT. IT IS RECOMMENDED THAT MOVING OR LIFTING THE UNIT BE DONE BY TWO PEOPLE TO AVOID INJURY.

￿CAUTION: FAILURE TO ALLOW ADEQUATE VENTILATION WILL VOID THE WARRANTY.

4.Remove cable tie used to secure motor during shipment. Make sure motor rocks freely. (see Figure D)

5.Connection of refrigeration system: The unit is supplied with mating quick disconnect

fittings. Removal of the rear panel will show: One 5/8” suction connection, one 3/8” liquid connection for each barrel. Connect unit to condensing unit using the quick disconnects supplied. Line sizing to the unit should be sized to minimize pressure drops through the suction and liquid lines. (see Figure E)

NOTE: This procedure must be done by a qualified technician.

6.3341A and 3352 – Connect autofill product feed hose from pump assembly to solenoids via the 1/4” tube in the rear of the machine. Page 35.

Figure D – Removing

Plastic Cable Tie

Figure E

Crathco® Remote Beverage Freezers

Page 5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model Model 3341A Grindmaster Corporation Page Table of Contents Freezer Application and Specifications OPERATOR’S Safety PrecautionsRemote Freezers Product Tips Carburetor AssemblyMix Considerations General Freezer SpecificationsInstalling your Freezer InstallationShipment Transit Review hopper contents to make sure all parts are available Mix Low Function Operation and AdjustmentsHow to Operate Consistency AdjustmentDisassembly and Cleaning Care and CleaningDrain and Rinse Figure Q Clean Valve Body ReassemblySanitizing and Refilling Turn panel switch to OFFRemote Pump Sanitizing Clean-In-Place Procedure Daily CleaningSuggested Daily Maintenance MaintenanceParts Replacement Schedule How to Change Back Lit Sign Merchandiser Bulb How to Adjust BeltPreventative Maintenance Procedure Every 6 to 12 Months Problem Possible Cause Solution Troubleshooting GuideCrathco Remote Beverage Freezers Exploded View Model 3341A Final Assembly Exploded View Model 3341 Final AssemblyPart Number Description Exploded View Model 3341 Stock AssemblyExploded View Model 3341A Base Assembly Exploded View Models 3341/3341A Base Assembly Refrigeration Exploded View Models 3341/3341A Motor AssemblyElectrical Box Model Electrical Box Model 3341A Model 3341 Wiring Diagram Model 3341 Ladder Diagram Model 3341A Wiring Diagram Model 3341A Ladder Diagram Exploded View Model 3352 Final Assembly Exploded View Model 3342 Final AssemblyPart Number Description Exploded View Model 3342 Stock AssemblyExploded View Model 3352 Stock Assembly Base Assembly Refrigeration Models 3342/3352 Exploded View Models 3342/3352 Motor AssemblyElectrical Box Model Model 3342 Wiring Diagram Model 3342 Wiring Ladder Diagram Model 3352 Wiring Diagram Model 3352 Ladder Diagram Model Autofill Connections for Models 3341APage Page Box 35020 Louisville, KY 40232 USA

3341, 3341A, 3352, 3342 specifications

Grindmaster has established a reputable name in the coffee and foodservice equipment industry, and the models 3342, 3352, 3341A, and 3341 are emblematic of their innovative approach and high-quality standards. These advanced grinders are designed to cater to the diverse needs of cafés, restaurants, and any establishment that prioritizes quality coffee preparation.

The Grindmaster 3342 model boasts a number of key features that set it apart. It has a durable construction that ensures longevity, making it ideal for busy environments. The 3342's grinding capacity is optimized for medium to high-volume settings, with a patented grinding system that consistently delivers a uniform grind. This is critical for achieving the best flavor extraction during brewing, as an even grind size increases the coffee's overall taste profile.

Similarly, the 3352 model enhances user experience with its intuitive interface, allowing operators to easily adjust grind settings to meet different coffee blends and brewing techniques. Its advanced digital controls provide precise adjustments, enabling baristas to fine-tune the grind size for espresso, drip coffee, or even French press, contributing to a versatile coffee menu.

The Grindmaster 3341A stands out with its advanced technology that enhances efficiency. This model features a high-torque motor designed to reduce heat transfer during grinding, which preserves the coffee's essential oils and aroma. Moreover, its silent operation technology minimizes noise, making it a perfect fit for modern cafés where ambiance is essential.

The Grindmaster 3341 is also noteworthy for its ease of maintenance. It comes equipped with removable grinding burrs that simplify the cleaning process, ensuring that coffee quality is maintained over time. With its sturdy build and efficient performance, this model can handle heavy use while delivering exceptional results.

In summary, the Grindmaster 3342, 3352, 3341A, and 3341 are powerful grinders engineered for performance, versatility, and ease of use. Their advanced characteristics, such as consistent grinding, digital controls, high-torque motors, and easy maintenance, make them indispensable tools for any coffee professional. With Grindmaster's commitment to quality, these models provide an excellent foundation for crafting perfect coffee, allowing businesses to thrive in an increasingly competitive market.
Top Page Image Contents