3M 800af-s manual Conveyor Systems

Page 22

Installation and Set-Up (Continued)

8.Install case sealer in production line. When installing the case sealer, be sure to observe the following guidelines.

a.Case sealer must be installed level – it is not designed to convey boxes uphill.

b.Infeed conveyor must convey boxes to case sealer at a speed not to exceed 0.30 m/s [60 f/m].

c.Precautions must be taken to prevent excessive box pressure against the case sealer infeed gate. This will help to prevent damage to the boxes and ensure proper performance.

d.Infeed and exit conveyors must provide straight entrance and exit of boxes to/from case sealer and exit conveyor must positively convey boxes away from machine.

e.Refer to Figure 2-3 for suggested conveyor types that can be used with the case sealer.

Figure 2-3 – Conveyor Systems

9.Adjust case sealer bed height. The adjustable legs provide different machine bed heights from 610 mm [24 inches] minimum to 890 mm

[35 inches] maximum.

Refer to Figure 2-4 and set the machine bed height as follows:

a.Block up the machine frame to allow adequate leg adjustment.

b.Loosen, but do not remove, two M8 x 1.25 mm socket head screws in one leg (use M6 hex key wrench). Adjust the leg length for the desired machine bed height. Retighten the two screws to secure the leg. Adjust all four legs equally.

10.Tape width – the taping heads have been pre- set to accommodate 72 mm [3 inch] wide tape

rolls. To apply narrower width tapes, refer to

Figure 2-4 – Conveyor Bed Height Adjustment

Section II, "Adjustments – Tape Web

 

Alignment".

 

14

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 3M-Matic 3M Industrial Adhesives and TapesPage To Our Customers Page 3M 2005 44-0009-1852-2E Page Table of Contents Section I AccuGlide SST 2 Inch Taping Heads Intended Use Contents 800af-s Stainless Steel Adjustable Case Sealer Important Safeguards Replacement Labels/3M Part Numbers Page Operator Skill Level Descriptions Skill 1 Machine Operator OperatorsPower Requirements SpecificationsOperating Rate Tape Width Operating ConditionsTape Tape Roll DiameterBox Weight and Size Capacities Dimensions are listed on the following Maximum Machine Dimensions MinimumSet-Up Recommendations Receiving And Handling Installation and Set-UpMachine Set-Up Installation and Set-Up Conveyor Systems Initial Start-Up of Case Sealer Pneumatic ConnectionOperation Controls, Valves and Switches Electrical On/Off Switch Main Air On/Off Valve/Pressure Regulator/Filter FigureIndicator, Air Pressure Height Adjustment Crank, Upper Taping HeadWidth Adjustment Crank Top Flap Compression RollersWith Tape Drum On Taping Head Tape Loading/Threading Upper Taping HeadTape Loading/Threading Lower Taping Head With Alternate Outboard Tape DrumBox Size Set-Up Operation 10 Box Size Set-Up 11 Box Size Set-Up Box Sealing 13 Box Size Set-UpTurn machine On only when it is safe to do so Box JamsCleaning MaintenanceLubrication Drive Belt Replacement/Tension Adjustment Drive Belt ReplacementDrive Belt Tension Adjustment Top View Air Line Filter Figure Knife Replacement, Taping HeadCircuit Breaker Gate Operation Drive Belt TensionAdjustments Upper Taping Head LevelingGate Stroke Setting Gate Pressure RegulatorThis page is Blank Special Set-Up Procedure Changing Drive Belt HeightOuter Column Re-Positioning Refer to Figure Column Re-Positioning Troubleshooting Troubleshooting Guide Problem Cause CorrectionTroubleshooting Pneumatic Diagram Pneumatic DiagramElectrical Diagram Electrical DiagramPage This page is Blank Spare and Miscellaneous Parts Options/Accessories Part Number Option/AccessoryReplacement Parts Illustrations and Parts Lists This page is Blank 800af Adjustable Case Sealer Frame Assemblies 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No M Part No Description 800af-s Adjustable Case Sealer Ref. No M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Pos Code Description 800af Adjustable Case Sealer Pos Code Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 1of Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No Code Description 800af Adjustable Case Sealer Ref. No 3M Part No Description Ref. No 3M Part No Description This page is Blank 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description This page is Blank

800af-s specifications

The 3M 800AF-S is an advanced particle filter that is widely recognized for its efficiency and adaptability in various industrial and occupational settings. Designed to combat particulate contaminants in the workplace, this filter exemplifies 3M’s commitment to innovation and safety.

One of the key features of the 3M 800AF-S is its exceptional particle filtration capability. It is engineered to capture a wide range of airborne particles, including dust, pollen, mold spores, and even some bacteria and viruses, making it a vital tool for industries such as healthcare, construction, and manufacturing.

The filter utilizes a unique electrostatic media technology that enhances its particle capture efficiency. This technology allows the filter to attract and trap smaller particles that might otherwise pass through conventional filters. With a high filtration efficiency rating, the 3M 800AF-S ensures that users are protected from harmful respiratory hazards.

Another noteworthy characteristic of the 3M 800AF-S is its low breathing resistance. This feature is crucial for maintaining comfort during extended wear, particularly in environments where workers may be required to wear a respirator for long hours. The low breathing resistance is achieved through an optimized design that balances the filter’s density and porosity, ensuring airflow without compromising on safety.

The 3M 800AF-S is also compatible with a range of 3M respirators, providing versatility for users across various applications. The easy-to-use design allows for quick attachment and detachment, ensuring that the filter can be replaced efficiently and conveniently when needed.

Furthermore, the 3M 800AF-S is equipped with a durable outer layer that enhances its lifespan and performance in challenging environments. This durability ensures that the filter maintains its integrity even under rigorous use, which is particularly beneficial in industrial settings where exposure to harsh conditions is common.

In summary, the 3M 800AF-S stands out in the market due to its superior filtration efficiency, low breathing resistance, compatibility with various respirators, and robust construction. As industries continue to prioritize worker safety, filters like the 3M 800AF-S are essential for ensuring a safer and healthier working environment.
Top Page Image Contents