3M 800af-s manual Air Line Filter Figure, Circuit Breaker, Knife Replacement, Taping Head

Page 37

Maintenance (Continued)

WARNING

•To reduce the risk associated with mechanical and electrical hazards:

–Turn electrical and air supply off and disconnect before performing any adjustments, maintenance or servicing the machine or taping heads

Air Line Filter – Figure 4-5

 

Periodically check the air line filter to drain water and

 

clean as necessary. Do not allow water to go above

 

the filter element.

 

Circuit Breaker

 

The case sealer is equipped with a circuit breaker

 

which trips if the motors are overloaded. Located

 

inside the electrical control box on the side of the

 

machine, the circuit breaker has been pre-set at

 

2.2 Amps and requires no further maintenance.

 

WARNING

 

• To reduce the risk associated with

 

mechanical and electrical hazards:

 

– Allow only properly trained and qualified

 

personnel to operate and/or service this

 

equipment

 

If circuit is overloaded and circuit breaker trips,

Figure 4-5 – Air Line Filter

 

unplug machine from electrical power:

 

1. Determine cause of overload and correct.

2. Remove electrical enclosure cover.

3. Press the red "Reset" button and then the green "Start" button.

4. Replace cover.

5. Plug in machine. Wait two minutes.

6. Press machine "On" button, on the side guard, to resume case sealing.

Knife Replacement, Taping Head

See Section II, "Maintenance – Blade (Knife)

Replacement".

29

Page 36 Page 38
Image 37
Page 36 Page 38
Contents 3M Industrial Adhesives and Tapes 3M-MaticPage To Our Customers Page 3M 2005 44-0009-1852-2E Page Table of Contents Section I AccuGlide SST 2 Inch Taping Heads Intended Use Contents 800af-s Stainless Steel Adjustable Case Sealer Important Safeguards Replacement Labels/3M Part Numbers Page Operators Operator Skill Level Descriptions Skill 1 Machine OperatorPower Requirements SpecificationsOperating Rate Tape Operating ConditionsTape Width Tape Roll DiameterBox Weight and Size Capacities Dimensions are listed on the following Maximum Machine Dimensions MinimumSet-Up Recommendations Receiving And Handling Installation and Set-UpMachine Set-Up Installation and Set-Up Conveyor Systems Pneumatic Connection Initial Start-Up of Case SealerOperation Main Air On/Off Valve/Pressure Regulator/Filter Figure Controls, Valves and Switches Electrical On/Off SwitchWidth Adjustment Crank Height Adjustment Crank, Upper Taping HeadIndicator, Air Pressure Top Flap Compression RollersTape Loading/Threading Lower Taping Head Tape Loading/Threading Upper Taping HeadWith Tape Drum On Taping Head With Alternate Outboard Tape DrumBox Size Set-Up Operation 10 Box Size Set-Up 11 Box Size Set-Up 13 Box Size Set-Up Box SealingBox Jams Turn machine On only when it is safe to do soCleaning MaintenanceLubrication Drive Belt Replacement Drive Belt Replacement/Tension AdjustmentDrive Belt Tension Adjustment Top View Air Line Filter Figure Knife Replacement, Taping HeadCircuit Breaker Drive Belt Tension Gate OperationUpper Taping Head Leveling AdjustmentsGate Pressure Regulator Gate Stroke SettingThis page is Blank Changing Drive Belt Height Special Set-Up ProcedureOuter Column Re-Positioning Refer to Figure Column Re-Positioning Troubleshooting Guide Problem Cause Correction TroubleshootingTroubleshooting Pneumatic Diagram Pneumatic DiagramElectrical Diagram Electrical DiagramPage This page is Blank Spare and Miscellaneous Parts Part Number Option/Accessory Options/AccessoriesReplacement Parts Illustrations and Parts Lists This page is Blank 800af Adjustable Case Sealer Frame Assemblies 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No M Part No Description 800af-s Adjustable Case Sealer Ref. No M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Pos Code Description 800af Adjustable Case Sealer Pos Code Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 1of Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No Code Description 800af Adjustable Case Sealer Ref. No 3M Part No Description Ref. No 3M Part No Description This page is Blank 800af-s Adjustable Case Sealer Ref. No 3M Part No Description 800af-s Adjustable Case Sealer Ref. No 3M Part No Description This page is Blank

800af-s specifications

The 3M 800AF-S is an advanced particle filter that is widely recognized for its efficiency and adaptability in various industrial and occupational settings. Designed to combat particulate contaminants in the workplace, this filter exemplifies 3M’s commitment to innovation and safety.

One of the key features of the 3M 800AF-S is its exceptional particle filtration capability. It is engineered to capture a wide range of airborne particles, including dust, pollen, mold spores, and even some bacteria and viruses, making it a vital tool for industries such as healthcare, construction, and manufacturing.

The filter utilizes a unique electrostatic media technology that enhances its particle capture efficiency. This technology allows the filter to attract and trap smaller particles that might otherwise pass through conventional filters. With a high filtration efficiency rating, the 3M 800AF-S ensures that users are protected from harmful respiratory hazards.

Another noteworthy characteristic of the 3M 800AF-S is its low breathing resistance. This feature is crucial for maintaining comfort during extended wear, particularly in environments where workers may be required to wear a respirator for long hours. The low breathing resistance is achieved through an optimized design that balances the filter’s density and porosity, ensuring airflow without compromising on safety.

The 3M 800AF-S is also compatible with a range of 3M respirators, providing versatility for users across various applications. The easy-to-use design allows for quick attachment and detachment, ensuring that the filter can be replaced efficiently and conveniently when needed.

Furthermore, the 3M 800AF-S is equipped with a durable outer layer that enhances its lifespan and performance in challenging environments. This durability ensures that the filter maintains its integrity even under rigorous use, which is particularly beneficial in industrial settings where exposure to harsh conditions is common.

In summary, the 3M 800AF-S stands out in the market due to its superior filtration efficiency, low breathing resistance, compatibility with various respirators, and robust construction. As industries continue to prioritize worker safety, filters like the 3M 800AF-S are essential for ensuring a safer and healthier working environment.
Top Page Image Contents