3M 39600 manual Initial Start-Up of Case Sealer, Pneumatic Connection

Page 19

Installation and Set-Up (Continued)

11.Box size capacity (height) – at its factory setting, the case sealer handles box sizes up to 620 mm

[24-1/2 inches] maximum height. If larger capacity is needed, the machine can be adjusted to accommodate up to 725 mm [28-1/2 inches] high boxes. Refer to "Special Set-Up Procedure – Outer Column Re-Positioning", page 35 for set-up information.

12.Drive Belt Height – drive belt assemblies can be raised 50 mm [2 inches] to provide better conveying of tall boxes. Refer to "Special Set-Up Procedure – Changing Drive Belt Height", page 33.

13.Pneumatic connection.

WARNING – USE CARE WHEN WORKING WITH COMPRESSED AIR.

The case sealer requires a 6.5 bar gauge pressure [95 PSIG] 75 liter/min @21°C, 1.01 bar [2.5 SCFM] compressed air supply. As shown in Figure 2-3 an on/off valve, pressure regulator, and filter are provided to service the air supply.

The main air supply line should be connected to the on/off valve by means of the barbed fitting and hose clamp provided on the outer side of the on/off valve as shown in Figure 2-3. The customer supplied air hose (5/16 inch [8 mm] ID) should be slipped over the barbed fitting and clamped tightly in place.

If another type of connector is desired, the fitting can be removed and replaced with the desired 1/4-18 NPT threaded connector.

Always turn the valve "Off" when air supply line is being connected or disconnected.

14.Electrical connection and controls – the electrical control box shown in Figure 3-1, contains the "On/Off" switch with pre-set breaker and can be located on either side of the machine frame for operator convenience. A standard three conductor power cord with plug is provided at the back of the electrical control box for 115 Volt, 60 Hz, 3.8 Amp electrical service. The receptacle providing this service shall be properly grounded. Before the power cord is plugged into 115 Volt, 60 Hz outlet, make sure red "Off" button is depressed and that all packaging materials and tools are removed from the machine. Do not plug electrical cord into outlet until ready to run machine.

Note – Machines outside the U.S. may be equipped with 220/240 Volt, 50 Hz systems, or other electrical requirements compatible with local practice.

Initial Start-Up of Case Sealer

 

After completing the "Set-Up" procedure, continue

 

through ""Operation", pages 15-24 to be sure case

Figure 2-3 – Pneumatic Connection

sealer is properly adjusted to run product.

14

Image 19
Contents AccuGlideTM To Our Customers Replacement Parts and Additional ManualsTo Our Customers 800af3 Adjustable Case Sealer Type Table of ContentSection II AccuGlide STD 3 Inch Taping Heads Intended Use 3M-Matic800af3 Adjustable Case Sealer, TypeContents 800af3 Adjustable Case Sealer Knife Warning Label Important SafeguardsMoving Flap Kicker Safety Instructions Label 13 Permissible Lift Area Label Power Requirements SpecificationsOperating Rate Tape Roll Diameter Operating ConditionsTape Tape WidthBox Weight and Size Capacities Maximum Machine Dimensions MinimumSet-Up Recommendations Receiving And Handling Installation and Set-UpMachine Set-Up Installation and Set-Up Conveyor Systems Pneumatic Connection Initial Start-Up of Case SealerCase Sealer Components OperationMain Air On/Off Valve/Pressure Regulator/Filter -3 Controls, Valves and Switches Electrical On/Off SwitchTop Flap Compression Rollers Height Adjustment Crank, Upper Taping HeadWidth Adjustment Crank Indicator, Air PressureSee Section II, Pages 7 Box Size Set-Up Operation Passing through machine to avoid injury Machine before operating11 Box Size Set-Up Feeding boxes to the machine13 Box Size Set-Up Occur Box SealingBox Jams Turn machine On only when it is safe to do soLubrication MaintenanceDrive Belt Replacement Damage Drive Belt Replacement/Tension AdjustmentDrive Belt Tension Adjustment Top View Equipment damage Air Line Filter -5 Knife Replacement, Taping HeadCircuit Breaker Taping Head Adjustments -Refer to Section AdjustmentsDrive Belt Tension Damage Upper Taping Head Leveling Gate Stroke Setting This page is Blank Drive Belt Height, Disassembly Special Set-Up ProcedureTaping Heads Outer Column Re-Positioning Refer to Figure Column Re-Positioning Troubleshooting Guide Problem Cause Correction TroubleshootingTroubleshooting Pneumatic Diagram Pneumatic DiagramElectrical Diagram Electrical DiagramPage This page is Blank Spare and Miscellaneous Parts Part Number Option/Accessory Options/AccessoriesReplacement Parts Illustrations and Parts Lists This page is Blank 800af3 Adjustable Case Sealer Frame Assemblies 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 1of Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Safety and Information Labels Ref. No 3M Part No Description Qty
Related manuals
Manual 72 pages 62.27 Kb Manual 70 pages 21.44 Kb Manual 64 pages 55.71 Kb Manual 70 pages 16.15 Kb

39600 specifications

The 3M 39600 is a high-quality, versatile adhesive designed to meet the needs of professionals across various industries. This product is particularly well-regarded for its exceptional bonding capabilities and ease of use, making it a popular choice among contractors, automotive professionals, and DIY enthusiasts alike.

One of the main features of the 3M 39600 is its strong adhesion to a wide range of substrates. This includes metals, plastics, glass, and composites, allowing users to bond different materials seamlessly. The adhesive forms a strong, durable bond that provides long-lasting performance, making it suitable for both interior and exterior applications.

Another key characteristic of the 3M 39600 is its fast curing time. The adhesive typically sets quickly, which is crucial in fast-paced work environments where time is of the essence. This rapid curing allows users to proceed with their projects without long wait times. Additionally, the adhesive exhibits high resistance to moisture and temperature fluctuations, ensuring that the bond remains secure even in challenging environmental conditions.

The technology behind the 3M 39600 is based on advanced polymer chemistry, which contributes to its reliable performance. The formulation of the adhesive results in excellent shear strength and tensile strength, making it ideal for demanding applications. The product is also designed to be user-friendly; it can be applied using various methods such as brush, roller, or spray, depending on the specific requirements of the project.

3M 39600 is often recognized for its versatility. It is suitable for applications in industries like automotive, construction, electronics, and appliance manufacturing. In the automotive sector, for example, it is used for bonding parts together, ensuring structural integrity and enhancing both performance and aesthetics.

In summary, the 3M 39600 adhesive is a top choice for those seeking a reliable and efficient bonding solution. Its strong adhesion, fast curing time, and advanced technology make it suitable for a variety of applications. Whether you are a professional or a DIY enthusiast, the 3M 39600 provides the performance you need to achieve quality results in your projects.