3M 39600 Equipment damage Air Line Filter -5, Circuit Breaker, Knife Replacement, Taping Head

Page 33

Maintenance (Continued)

WARNING – Turn air and electrical supplies off and disconnect before beginning maintenance. Failure to comply with this warning could result in severe personal injury or

equipment damage.

Air Line Filter –Figure4-5

Periodically check the air line filter to drain water and clean as necessary. Do not allow water to go above the filter element.

Circuit Breaker

 

The case sealer is equipped with a circuit breaker

 

which trips if the motors are overloaded. Located

 

inside the electrical control box on the side of the

 

machine, the circuit breaker has been pre-set at

 

2.2 Amps and requires no further maintenance.

 

WARNING – The following procedure

 

must be performed by trained service

 

personnel because of the high voltage

 

electrical hazard within the control box.

 

If circuit is overloaded and circuit breaker trips,

Figure 4-5 – Air Line Filter

 

unplug machine from electrical power:

 

1.Determine cause of overload and correct.

2.Remove electrical enclosure cover.

3.Press the red "Reset" button and then the green "Start" button.

4.Replace cover.

5.Plug in machine. Wait two minutes.

6.Press machine "On" button, on the side guard, to resume case sealing.

Knife Replacement, Taping Head

See Section II, "Maintenance – Blade (Knife)

Replacement", page 9.

28

Page 32 Page 34
Image 33
Page 32 Page 34
Contents AccuGlideTM To Our Customers Replacement Parts and Additional ManualsTo Our Customers 800af3 Adjustable Case Sealer Type Table of ContentSection II AccuGlide STD 3 Inch Taping Heads Intended Use 3M-Matic800af3 Adjustable Case Sealer, TypeContents 800af3 Adjustable Case Sealer Knife Warning Label Important SafeguardsMoving Flap Kicker Safety Instructions Label 13 Permissible Lift Area Label Specifications Power RequirementsOperating Rate Tape Operating ConditionsTape Width Tape Roll DiameterBox Weight and Size Capacities Machine Dimensions Minimum MaximumSet-Up Recommendations Installation and Set-Up Receiving And HandlingMachine Set-Up Installation and Set-Up Conveyor Systems Pneumatic Connection Initial Start-Up of Case SealerCase Sealer Components OperationMain Air On/Off Valve/Pressure Regulator/Filter -3 Controls, Valves and Switches Electrical On/Off SwitchWidth Adjustment Crank Height Adjustment Crank, Upper Taping HeadIndicator, Air Pressure Top Flap Compression RollersSee Section II, Pages 7 Box Size Set-Up Operation Passing through machine to avoid injury Machine before operating11 Box Size Set-Up Feeding boxes to the machine13 Box Size Set-Up Occur Box SealingBox Jams Turn machine On only when it is safe to do soLubrication MaintenanceDrive Belt Replacement Damage Drive Belt Replacement/Tension AdjustmentDrive Belt Tension Adjustment Top View Knife Replacement, Taping Head Equipment damage Air Line Filter -5Circuit Breaker Adjustments Taping Head Adjustments -Refer to SectionDrive Belt Tension Damage Upper Taping Head Leveling Gate Stroke Setting This page is Blank Drive Belt Height, Disassembly Special Set-Up ProcedureTaping Heads Outer Column Re-Positioning Refer to Figure Column Re-Positioning Troubleshooting Guide Problem Cause Correction TroubleshootingTroubleshooting Pneumatic Diagram Pneumatic DiagramElectrical Diagram Electrical DiagramPage This page is Blank Spare and Miscellaneous Parts Part Number Option/Accessory Options/AccessoriesReplacement Parts Illustrations and Parts Lists This page is Blank 800af3 Adjustable Case Sealer Frame Assemblies 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 1of Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Ref. No 3M Part No Description 800af3 Adjustable Case Sealer Safety and Information Labels Ref. No 3M Part No Description Qty
Related manuals
Manual 72 pages 62.27 Kb Manual 70 pages 21.44 Kb Manual 64 pages 55.71 Kb Manual 70 pages 16.15 Kb

39600 specifications

The 3M 39600 is a high-quality, versatile adhesive designed to meet the needs of professionals across various industries. This product is particularly well-regarded for its exceptional bonding capabilities and ease of use, making it a popular choice among contractors, automotive professionals, and DIY enthusiasts alike.

One of the main features of the 3M 39600 is its strong adhesion to a wide range of substrates. This includes metals, plastics, glass, and composites, allowing users to bond different materials seamlessly. The adhesive forms a strong, durable bond that provides long-lasting performance, making it suitable for both interior and exterior applications.

Another key characteristic of the 3M 39600 is its fast curing time. The adhesive typically sets quickly, which is crucial in fast-paced work environments where time is of the essence. This rapid curing allows users to proceed with their projects without long wait times. Additionally, the adhesive exhibits high resistance to moisture and temperature fluctuations, ensuring that the bond remains secure even in challenging environmental conditions.

The technology behind the 3M 39600 is based on advanced polymer chemistry, which contributes to its reliable performance. The formulation of the adhesive results in excellent shear strength and tensile strength, making it ideal for demanding applications. The product is also designed to be user-friendly; it can be applied using various methods such as brush, roller, or spray, depending on the specific requirements of the project.

3M 39600 is often recognized for its versatility. It is suitable for applications in industries like automotive, construction, electronics, and appliance manufacturing. In the automotive sector, for example, it is used for bonding parts together, ensuring structural integrity and enhancing both performance and aesthetics.

In summary, the 3M 39600 adhesive is a top choice for those seeking a reliable and efficient bonding solution. Its strong adhesion, fast curing time, and advanced technology make it suitable for a variety of applications. Whether you are a professional or a DIY enthusiast, the 3M 39600 provides the performance you need to achieve quality results in your projects.
Top Page Image Contents