Miele DA217-3, DA 219-3 Plywood backing, To install a plywood backing board

Page 26

Plywood backing

The majority of the weight of the installed ventilation system will be supported by retaining plate A. It must be firmly attached to the stud framing behind the drywall. If studs are not available in the required locations, a plywood backing (min.

1/2" (13 mm) thick) spanning at least two studs must be installed. Failure to adequately support the weight as stated may result in the ventilation system falling off the wall, causing personal injury and property damage.

(If plywood backing is not needed, proceed to "Attaching the retaining plates to the wall." )

To install a plywood backing board

^Make a mark, S + 16 3/4" (425 mm) above the cooktop and on the centerline.

^Make a second mark 12 3/4 "

(324 mm) underneath the first one.

^Hold retaining plate A against the wall so that the marks are visible through the holes of the plate (see "Installation / Retaining plate A"). Draw a line around the plate’s perimeter, then set aside the plate.

^Make a cutting line 3" (76 mm) above and 3" (76 mm) below the outline of plate "A".

^Find the studs to the left and right of the mounting location by tapping the wall or using a stud finder.

^Mark a vertical cutting line along the center of each stud.

Be careful not to damage any wiring or plumbing that may be located behind the wall. Make sure that the power supply to the area where this installation is being performed has been turned off at the breaker panel before cutting into the wall.

^Remove the drywall between the cutting lines and replace it with

plywood of a matching thickness (min. 1/2" (13 mm) thick). Tape the joints and refinish the wall.

^Proceed to "Attaching the Retaining plates to the wall" to complete the installation.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Operating and Installation Instructions Ventilation System Page Contents Important Safety Instructions Use Evacuate and Call the Fire Department Only ifInstallation To reduce the risk of fire only use metal ductworkGuide to the appliance Charcoal filter button Delayed Shut DownGrease filter button Air extraction Recirculation modeFunctional description Operation Turning on the fan Selecting the power levelIntensive setting Fan performanceTurning the lighting on/off Automatic Safety Shut OffTurning off the fan Dimming the lightingGrease filters Filter timersChecking the filter timers Charcoal filtersReprogramming the timers Reprogramming the grease filter timerReprogramming the charcoal filter timer Stainless steel Cleaning and CareCleaning the casing Stainless steel colored controlsGrease filters Active charcoal filters Changing the light bulb After Sales Service Installation Instructions Page Disposal of an old appliance Caring for the environmentDisposal of packing material Installation accessories Diverter recirculation mode only Reducing collarTo install a plywood backing board Plywood backingElectrical data This Appliance Must be GroundedAppliance dimensions Appliance dimensions Extraction Recirculation Appliance dimensions Installation Retaining plates Attaching the retaining plates To the wallRetaining plate a Retaining plate BAttaching the canopy Retaining plate CInserting the non-return flap Attaching the motor assembly Electrical connection Air extraction exhaust connectionRecirculation connection Attaching the chimney extension Recirculation Air extraction Attaching the chimney Installation Air extraction Condensate trap Alteration rights reserved

DA 219-3, DA217-3 specifications

The Miele DA 219-3 and DA 217-3 are powerful and stylish range hoods that exemplify Miele's commitment to quality and innovation in kitchen ventilation. These models are designed to enhance the culinary experience while ensuring a clean and fresh environment in the kitchen.

One of the standout features of both models is their exceptional extraction performance. With powerful motors, the DA 219-3 and DA 217-3 are capable of efficiently eliminating smoke, odors, and airborne grease particles, ensuring that your kitchen remains comfortable and inviting. Both units operate quietly, making it easy to have conversations and enjoy the cooking process without disruptive noise.

These range hoods are equipped with advanced technologies that enhance their usability and performance. The intensive speed setting provides a temporary boost in extraction power, quickly clearing the air when needed. This feature is particularly useful during heavy cooking or when frying, ensuring that strong odors and smoke are dealt with promptly.

The Miele CleanCover provides an additional layer of convenience, ensuring that the internal components of the hood are easily accessible for cleaning, while also protecting users from sharp edges and metal parts. Maintenance is further simplified with the reusable metal grease filters, which can be easily removed and washed in a dishwasher, ensuring that the hoods maintain their efficiency over time.

Both models incorporate Miele's innovative ducted and recirculation options, allowing for flexibility based on kitchen layout and design preferences. Whether you prefer to vent air outside or recirculate it within the kitchen, these hoods can adapt to your needs.

In terms of design, the DA 219-3 and DA 217-3 showcase a sleek and modern aesthetic, seamlessly fitting into a variety of kitchen styles. The intuitive user interface, including simple control buttons, makes operation effortless, allowing users to adjust settings with ease.

In summary, the Miele DA 219-3 and DA 217-3 range hoods provide a blend of power, efficiency, and design sophistication. With their high extraction rates, advanced features, easy maintenance, and stylish appearance, they are an excellent choice for anyone looking to elevate their kitchen experience while maintaining a pleasant atmosphere. Whether you're an amateur cook or a seasoned chef, these range hoods deliver the performance and reliability you expect from Miele.
Top Page Image Contents