GE JVB67, JVB37, JVB98 Install the RAISE/LOWER Switch, Connect Raise/Lower Wire Lead to Wire Box

Page 16

Installation Instructions

INSTALLING THE DOWNDRAFT VENT SYSTEM

3INSTALL THE RAISE/LOWER SWITCH

NOTE: Step 3 is for 36″ models only. Skip this step if installing a 30″ model.

WARNING — Disconnect electrical power from the unit before beginning switch installation. Failure to do so could result in personal injury or damage to the electrical controls.

NOTE: Determine the location for the Raise/Lower switch. The wiring lead is 68″ long.

Raise/Lower

Trim

switch

 

Mounting bracket

 

3/8″ Hole

Pull 3″

2 Pin

length

out of

connector

box

 

 

Strain relief

ADrill a 3/8″ hole into the desired location. Use the mounting bracket as a template to locate the hole accurately. Check for interference between the switch cover, adjacent objects and cooktop/vent overlaps.

BIf switch is mounted into a tile surface, drill the hole between tiles. Use locally approved caulking to cover any gaps.

CCenter the mounting bracket over the hole and mark pilot holes. Remove and drill holes according to type of countertop.

DMount the metal switch bracket with screws (not provided). Choose screws for your type of countertop or use locally approved adhesive.

ERemove protective film from the top of the switch trim.

FPeel film from the adhesive strips on the back of the switch trim. Thread the wire lead through the mounting bracket and countertop. Press trim over the mounting bracket to set the adhesive.

Connect Raise/Lower Wire Lead to Wire Box

AThread wire end with the connector

through the hole on the end of a wire box. Pull approximately 3″ additional wire length beyond the open end of the box.

BConnect the mating wire connectors.

CInstall the wire box onto the bottom of the countertop or directly behind the switch. Use screws or adhesive appropriate for the type of countertop.

DPlace plastic strain relief over the wire, just outside of the hole at the end of the wire box. Do not pinch or twist the wire. Snap the strain relief closed and press into the hole.

Control box

Connect Wire Lead to Control Box

AThread the long 68″ wire lead through the end of the other wire box.

BPush wire leads into the white connector provided.

CPush wire connector into the mating connector on the control box. Install the wire box onto the end of the control box with screws provided.

DPlace plastic strain relief over the wire, just outside of the hole at the end in the wire box. Do not pinch or twist the wire. Snap the strain relief closed and press into the hole.

ECoil the excess wire and position away from moving parts and cabinet contents.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Vent Systems Safety Precautions Safety Precautions Raise/Lower Switch 30 ″ models only Using the downdraft systemUsing the Cooktop Care and cleaning of the downdraft system Cooking TipsGrease Filters Painted or Metal SurfacesBefore YOU Begin Tools YOU will NeedRemove Packaging Parts IncludedInstallation Instructions Dimensions and ClearancesRemote Switch ClearancesDuctwork Cooktop Electrical and GAS LocationInstallation Possibilities Installing the Downdraft Vent System 30″ COOKTOP/DOWNDRAFT Units JVB37 and JVB9436″ COOKTOP/DOWNDRAFT Units JVB67 and JVB98 Gas Cooktops Power SupplyElectric Cooktops Ductwork Length and Duct Fittings Should not Exceed 150 Equivalent FeetSide-to-Side Adjustments Venting OptionsDischarge Direction To Change to a Left or Right DischargeInstall the Downdraft Vent Install the DuctworkConnect Raise/Lower Wire Lead to Wire Box Install the RAISE/LOWER SwitchConnect Wire Lead to Control Box Install the Cooktop Connect the PowerOptional Kits Before you call for service… Troubleshooting TipsGE Will Replace GE Downdraft System WarrantyWhat GE Will Not Cover Schedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design StudioSistemasde ventilación ¡ADVERTENCIA Advertencia Para Reducir Soporte al consumidorOperación Uso de la estufaCuidado y limpieza del sistema de tiro descendente Antes DE Empezar Herramientas NecesariasRetiro DEL Empaque Partes IncluidasDimensiones Y Espacios Instrucciones de instalaciónEspacios DuctosUbicación DE LA Conexión Eléctrica Y DE GAS DE LA Estufa Interruptor RemotoPosibilidades DE Instalación Instalación DEL Sistema DE Ventilación DE Tiro Descendente JVB98 Estufas a gas Suministro DE CorrienteEstufas eléctricas Longitud DEL Conducto Y Accesorios No SE Debe Exceder EL Equivalente a 150 PiesOpciones DE Ventilación Ajustes de lado a ladoDirección de la descarga Para cambiar la descarga hacia la izquierda o derechaInstale EL Ventilador DE Tiro Descendente Instale EL ConductoInstalación DEL Sistema DE Ventilación DE Tiro Descendente Conecte el cable en la caja de controlInstale LA Estufa Conecte LA CorrienteKits Opcionales Problema Posibles causas Qué hacer Antes de llamar a solicitar servicio…Solucionar problemas Garantía del sistema de tiro descendente de GEGE reemplazará Qué no cubre GESoporte al consumidor Página Web de GE Appliances Solicite una reparaciónGarantías ampliadas Piezas y accesorios
Related manuals
Manual 20 pages 22.34 Kb Manual 20 pages 37.21 Kb

JVB94, JVB98, JVB37, JVB67 specifications

The GE JVB37 and JVB67 are advanced connected commercial water heaters designed to meet the challenges of modern facilities while prioritizing efficiency, safety, and reliability. With an acute emphasis on smart technology, these models provide user-friendly features and robust performance for various applications, including restaurants, hotels, and multi-family buildings.

One of the standout features of the GE JVB37 and JVB67 is their energy efficiency. Both models utilize a state-of-the-art heat pump technology, which allows them to consume significantly less energy compared to traditional electric or gas-fired water heaters. This results in lower operating costs and a reduced environmental footprint, making them ideal choices for businesses looking to enhance their sustainability efforts.

The JVB37 has a 37-gallon capacity, while the JVB67 offers a larger 67-gallon capacity, catering to different usage requirements. These models are equipped with an intuitive digital interface that provides real-time monitoring and control, ensuring users can easily adjust the temperature settings and monitor energy consumption. Moreover, the connectivity features enable remote management through mobile apps or smart devices, providing added convenience for facility managers.

In terms of safety, both models incorporate advanced features such as leak detection, automatic shut-off valves, and tamper-proof designs. These safeguards help prevent potential hazards while ensuring a reliable supply of hot water. Furthermore, the build quality of the JVB37 and JVB67 reflects GE's commitment to longevity, with durable materials that resist corrosion and wear, ensuring years of dependable service.

The installation of the JVB37 and JVB67 is simplified due to their compact designs, allowing for flexibility in various settings. Whether mounted on the wall or positioned in tight spaces, these water heaters can adapt to different layouts without compromising performance.

Overall, the GE JVB37 and JVB67 are exemplary models in the market of connected commercial water heaters, seamlessly blending innovation with practicality. Their energy-efficient operation, combined with smart technologies and robust safety features, makes them ideal solutions for businesses aiming to optimize their hot water needs while prioritizing sustainability and efficiency.
Top Page Image Contents