GE LMAB1240ST Measurement with Outer Case Removed, Measurement with a Fully Assembled Oven

Page 13

MEASUREMENT WITH OUTER CASE REMOVED

•When you replace the magnetron, measure for microwave energy leakage before the outer case is installed and after all necessary components are replaced or adjusted.

Special care should be taken in measuring the following parts. (Circled area of Fig. below)

-Around the magnetron

-The waveguide

WARNING : AVOID CONTACTING ANY HIGH VOLTAGE PARTS

MEASUREMENT WITH A FULLY ASSEMBLED OVEN

•After all components, including the outer case, are fully assembled, measure for microwave energy leakage around the door viewing window, the exhaust opening, and air inlet openings.

•Microwave energy leakage must not exceed the values prescribed below.

NOTE: Leakage with the outer case removed less than 5 mW/cm.sq. Leakage for a fully assembled oven (Before the latch switch (primary) is interrupted) with the door in a slightly opened position-less than 2 mW/cm.sq.

NOTES WHEN MEASURING

•Do not exceed meter full scale deflection.

•The test probe must be moved no faster than

1 inch/sec (2.5 cm/sec) along the shaded area, otherwise a false reading may result.

•The test probe must be held by the grip portion of the handle.

A false reading may result if the operator's hand is between the handle and the probe.

•When testing near a corner of the door, keep the probe perpendicular to the surface making sure the probe horizontally along the oven surface. Hold vertically when testing the top and bottom, and horizontally along.

RECORD KEEPING AND NOTIFICATION AFTER MEASUREMENT

•After adjustment and repair of any microwave energy interruption or microwave energy blocking device, record the measured values for future reference. Also enter the information on the service invoice.

•The microwave energy leakage should not be more than 4 mW/cm.sq. after determining that all parts are in good condition, functioning properly and genuine replacement parts which are listed in this manual have been used.

•At least once a year, have the electromagnetic energy leakage monitor checked for calibration by its manufacturer.

SPECIAL TIP

•This oven used the button head screws.

Button Head (Torx style 2)

•When you remove the screws, use

the tamper-resistant Torx driver having a pin-in-head.

5-2

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Microwave Oven Microwave Radiation Safety PrecautionsContents Description SpecificationsAntenna Microwave RadiationInstalling InstallationGrounding Instructions Operating Instructions FeaturesControl Panel Operating Sequence Schematic Diagram I *Check the Rating Model No Page Circuit Description Tools and Measuring Instruments Service InformationMicrowave Leakage Test Necessary ToolsMeasurement with a Fully Assembled Oven Measurement with Outer Case RemovedDisassembly and Adjustment Measurement of Microwave Power OutputPower Supply Cord Control Panel AssemblyDoor Assembly Removal PCB Assembly RemovalRemoving the Turntable Motor Magnetron RemovalVery Carefully High Voltage Transformer Removal FAN Motor Assembly RemovalHigh Voltage Capacitor and Diode Removal Iinterlock SystemSecondary Interlock Switch Test Primary Interlock Switch TestMonitor Switch Test SwitchesFilament Winding Primary Terminal Component Test ProcedureMagnetron Capacitor High VoltageDiode Relay PowerLevel FAN MotorCondition Cause Remedy Trouble ShootingResult Result Condition Check Defective high voltage transformer Introduction Exploded ViewDoor Parts Control Panel Parts Oven Cavity Parts Larch Board Parts Model LMAB1240ST Interiot Parts56201A Base Plate Parts

LMAB1240ST specifications

The GE LMAB1240ST is a remarkable side-by-side refrigerator that embodies modern design and advanced technology, catering to the needs of today's consumers. Offering a perfect blend of style, functionality, and efficiency, this model stands out in the crowded marketplace.

One of the main features of the LMAB1240ST is its spacious interior. With a generous capacity of 24.9 cubic feet, this refrigerator provides ample storage for families and individuals alike. The side-by-side configuration allows easy access to both fresh and frozen foods, making organization simple and efficient.

In terms of cooling technology, the LMAB1240ST uses advanced climate control features. The refrigerator is equipped with a multi-air flow system that ensures consistent airflow throughout the unit. This technology helps maintain even temperatures, keeping food fresher for longer. Additionally, the adjustable shelves allow for customization of the interior space, accommodating various sizes of food items and containers.

The GE LMAB1240ST emphasizes energy efficiency as well. It is Energy Star certified, indicating that it meets or exceeds energy efficiency guidelines set by the U.S. Environmental Protection Agency. This not only helps reduce utility bills but also minimizes environmental impact, which is a consideration for eco-conscious consumers.

Another significant feature of this model is its water and ice dispenser. The dispenser is designed to provide chilled water and cubed/crushed ice right at your fingertips. It is conveniently located on the front of the refrigerator for easy access. The filter system ensures that the water dispensed is clean and free from contaminants, enhancing safety and taste.

Additionally, the LMAB1240ST boasts advanced convenience features such as LED lighting, which provides bright and energy-efficient illumination within the refrigerator and freezer compartments. The easy-to-use temperature controls allow users to adjust settings effortlessly, ensuring optimal conditions for food storage.

Lastly, the stainless steel finish of the GE LMAB1240ST not only adds a sleek and contemporary look but also resists fingerprints and smudges, making maintenance more manageable. With a combination of innovative features, energy efficiency, and stylish aesthetics, the GE LMAB1240ST is an exceptional choice for anyone looking to upgrade their kitchen appliance.
Top Page Image Contents