GE JGRP17 Care and cleaning of the oven, Broiler Pan and Grid, Removable Storage Drawer

Page 25

Care and cleaning of the oven.

Be sure electrical power is off and all surfaces are cool before cleaning any part of the oven.

Safety

Pan

Grid

Broiler Pan and Grid

After broiling, remove the broiler pan from the oven. Remove the grid from the pan. Carefully pour out grease from the pan into a proper container. Wash and rinse the broiler pan and grid in hot water with a soap-filled or plastic scouring pad.

If food has burned on, sprinkle the grid with detergent while hot and cover with wet paper towels or a dishcloth. Soaking the pan will remove burned-on foods.

The broiler pan and grid may be cleaned with a commercial oven cleaner.

Both the broiler pan and grid can also be cleaned in a dishwasher.

Do not store a soiled broiler pan and grid anywhere in the oven.

CAUTION: Do not clean the broiler pan or grid in a self-cleaning oven.

Instructions

Removable Storage Drawer

The storage drawer is a good place to store cookware and bakeware. Do not store plastics and flammable material in the drawer.

Do not overload the storage drawer. If the drawer is too heavy, it may slip off the track when opened. To open the drawer, grasp the center of the handle and pull straight out.

Most cleaning can be done with the drawer in place. However, the drawer may be removed if further cleaning is needed. Use soap and warm water to thoroughly clean.

To remove:

Pull the drawer straight out and lift over the guide stops.

To replace:

Lift over the guide stops and slide the drawer into place.

To clean both the inside and the outside:

Wipe with soap and water. Rinse well.

Do not use cleansing powders or harsh abrasives which may scratch the surface.

Operating Instructions

Oven Air Vents

Never block the vents (air openings) of the oven. They provide the air inlet and outlet that are necessary for the oven to operate properly with correct combustion.

Air openings are located under the control panel, above the door.

Oven Light Replacement

Troubleshooting Tips

Wire cover holder

CAUTION: Before replacing your oven light bulb, disconnect the electrical power to the oven at the main fuse or circuit breaker panel. Be sure to let the light cover and bulb cool completely.

The oven light bulb is covered with a removable glass cover that is held in place with a bail-shaped wire. Remove the oven door, if desired, to reach the cover easily.

To remove:

Hold a hand under the cover so it doesn’t fall when released. With fingers of the same hand, firmly push back the wire cover holder. Lift off the cover.

Do not remove any screws to remove the cover.

Do not touch hot bulb with a wet cloth. Replace bulb with a 40-watt household appliance bulb.

To replace cover:

Place it into the groove of the light receptacle. Pull the wire forward to the center of the cover until it snaps into place. When in place, the wire holds the cover firmly. Be certain the wire is in the depression in the center of the cover.

Connect electrical power to the oven.

25

Customer Service

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Wall OvenBuilt-In Gas What to do if YOU Smell GAS Two easy ways to register your appliance GE & You, a Service PartnershipImportant Safety Notice Safety Precautions Oven Oven Control, Clock and Timer Features and Settings Using the oven controlsTimer Using the clock and timerHow to Set the Timer ClockTones While Setting the Control Power FailurePreheat Notification Tone Tones at the End of a Timed Cycle Special features of your oven controlHour Shut-Off Cook and HoldHour, 24-Hour or Clock Black-Out Fahrenheit or Centigrade Temperature SelectionControl Lockout Changing the Speed of the +/- PadsUsing the oven Oven Moisture Shelf PositionsOven Shelves How to Set Your Oven for Baking Using the baking featureOven Shelves PreheatingBaking Pans Pan PlacementCookies PiesTouch the Clock pad How to Set Delay Start and Automatic Stop To Adjust the Thermostat Adjust the oven thermostat-Do it youselfType of margarine will affect baking performance How to Set Your Oven for Roasting Using the roasting featureBefore You Begin Roasting… Roasting Guide Questions and AnswersHow to Set Your Oven for Broiling Using the broiling featureTroubleshooting Tips Before You Begin Broiling…Usda Rev. June Broiling GuideBefore a Clean Cycle Using the self-cleaning ovenHow to Set the Oven for Cleaning SafetyAfter a Clean Cycle Oven Light Replacement Care and cleaning of the ovenBroiler Pan and Grid Removable Storage DrawerRemovable Oven Bottom Self-clean cycleControl Panel To clean the outside of the door To clean the inside of the doorLift-Off Oven Door Broil and Oven Burner Air Adjustment Shutters Adjusting Orifice HoodsBefore You Call For Service… Clean cycle After a clean cycle Oven not clean after aCrackling or Popping soundCall for service On outer cones Power outageDisplay goes blank Display flashesPage We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration GE Will Replace, At No Charge To You GE Gas Oven WarrantyWhat GE Will Not Cover One YearGE Answer Center Service Telephone Numbers

JGRP17 specifications

The GE JGRP17 is a cutting-edge gas turbine engine designed primarily for use in industrial applications, distinguishing itself with a blend of advanced technology and robust performance. This engine is part of GE’s extensive portfolio of gas turbine systems, which are renowned for their efficiency, reliability, and adaptability.

One of the main features of the JGRP17 is its high thermal efficiency, enabling it to convert a greater proportion of fuel energy into usable power. This efficiency is achieved through sophisticated aerodynamic design and advanced materials that withstand high temperatures, resulting in lower fuel consumption and reduced emissions. The engine's modular design also contributes to its high performance, allowing for easier maintenance and reduced downtime during repairs or overhauls.

Another notable characteristic of the JGRP17 is its versatility. It can operate on a variety of fuels, including natural gas and liquid fuels, making it suitable for diverse applications across multiple sectors, from power generation to marine propulsion. The engine is engineered to provide reliable operation in various environmental conditions, ensuring consistent performance regardless of location.

The JGRP17 incorporates advanced control systems that enhance its operational efficiency and reliability. These systems utilize real-time monitoring and data analytics to optimize performance and detect potential issues before they escalate, thereby improving overall safety and operational longevity. These smart technologies are complemented by GE's legacy of engineering excellence, resulting in an engine that not only meets current industry standards but also anticipates future demands.

In addition to technical advancements, the GE JGRP17 is designed with sustainability in mind. Its lower emissions profile is a significant advantage in today’s climate-conscious market, facilitating compliance with stringent environmental regulations. The turbine's efficient performance contributes to reduced carbon footprints, making it an attractive option for companies looking to enhance their sustainability practices.

Overall, the GE JGRP17 gas turbine engine exemplifies the convergence of advanced engineering, efficiency, and environmental responsibility. With its powerful performance, flexible fuel options, and commitment to sustainability, it represents a significant advancement in industrial gas turbine technology, positioning itself as a reliable choice for a variety of energy and propulsion applications in an evolving marketplace.
Top Page Image Contents