GE JVM1790 A4. MOUNT THE OVEN, A3. ASSEMBLE AND INSTALL ADAPTOR, IMPORTANT If filler blocks are

Page 13
A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

Installation Instructions

A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET

You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.

Read the instructions on the TOP CABINET TEMPLATE.

Tape it underneath the top cabinet.

Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

A4. MOUNT THE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS OVEN.

IMPORTANT: Do not grip or use handle during installation.

NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord.

NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are

not used, case damage may occur from overtightening screws.

CAUTION: Wear safety goggles when drilling holes in the cabinet bottom.

A3. ASSEMBLE AND

INSTALL ADAPTOR

Damper

A4. MOUNT THE OVEN Exhaust

Adaptor

Blower Plate

Back of

Oven

1 Place the oven in its upright position, with the top

of the unit facing up.

NOTE: When mounting the oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3.

Do not pinch cord or lift oven by pulling cord.

2Rotate front of oven up against cabinet bottom.

1

Lift oven, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate.

2

Insert the tabs on each side of the damper into the

 

holes at the inside rear of the adaptor.

3

Attach the exhaust adaptor to the blower plate with

 

the two bronze metal screws provided.

 

Make sure that the damper pivots easily before

 

mounting oven.

 

You will need to make adjustments to assure proper

 

alignment with your house exhaust duct after the

 

oven is installed.

3Insert a self-aligning screw through top center cabinet hole. Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet.

13

Image 13
Contents READ CAREFULLY KEEP THESE INSTRUCTIONS BEFORE YOU BEGINInstallation Instructions Above the Cooktop OvenCONTENTS Installation InstructionsStep-by-step installation guide General informationELECTRICAL REQUIREMENTS Installation Instructions IMPORTANT SAFETY INSTRUCTIONSOUTSIDE TOP EXHAUST EXAMPLE ONLY Installation Instructions HOOD EXHAUSTOUTSIDE BACK EXHAUST EXAMPLE ONLY Total LengthMaximum duct length Exhaust connectionTotal Ductwork Ft. or mPARTS INCLUDED DAMAGE-SHIPMENT/ INSTALLATIONADDITIONAL PARTS HARDWARE PACKETMOUNTING SPACE Installation Instructions TOOLS YOU WILL NEEDThe depth of the opening cannot be more than 13-1/2” 34.3 cm A. REMOVING THE OVEN FROM THE CARTON/REMOVING THE MOUNTING PLATE Installation Instructions 1 PLACEMENT OF THE MOUNTING PLATEB. FINDING THE WALL STUDS Plate position-beneath flat bottom C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINETPlate position-beneath framed recessed cabinetSet the mounting plate aside D. ALIGNING THE WALL PLATEOUTSIDE TOP EXHAUST VERTICAL DUCT INSTALLATION TYPES Choose A, B or COUTSIDE BACK EXHAUST HORIZONTAL DUCT RECIRCULATING NON-VENTED DUCTLESSOUTSIDE TOP EXHAUST Vertical Duct INSTALLATION OVERVIEWA1. ATTACH THE MOUNTING PLATE TO THE WALL To use toggle boltsIMPORTANT Do not grip or use handle during installation A3. ASSEMBLE AND INSTALL ADAPTORA4. MOUNT THE OVEN A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINETA6. CONNECTING DUCTWORK A5. ADJUST THE EXHAUST ADAPTORA4. MOUNT THE OVEN continued B2. ATTACH THE MOUNTING PLATE TO THE WALL Installation Instructions B OUTSIDE BACK EXHAUST Horizontal DuctB1. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST B4. ADAPTING BLOWER FOR OUTSIDE BACK EXHAUST B3. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINETBEFORE Fan Blade Openings Facing Up7 Place the blower unit back into the opening INSTALL THIS MICROWAVE OVEN B5. MOUNT THE MICROWAVE OVENC1. ATTACH THE MOUNTING PLATE TO THE WALL RECIRCULATING Non-Vented DuctlessC2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET C3. ADAPTING BLOWER FOR RECIRCULATION C4. MOUNT THE OVEN C3. ADAPTING BLOWER FOR RECIRCULATION continuedEquivalent to Depth of Cabinet Recess C5. MOUNT THE OVEN continued C6. INSTALLING THE CHARCOAL FILTERScrews Side Screw Insert mesh-side downINSTALLATION INSTRUCTIONS Installation Instructions BEFORE YOU USE YOUR MICROWAVE06-05 JR 49-40453
Related manuals
Manual 76 pages 59.89 Kb

JVM1790 specifications

The GE JVM1790 is a versatile over-the-range microwave designed to enhance any kitchen with its stylish look and array of features, making it a popular choice among homeowners. This model combines functionality with an efficient space-saving design, ideal for those looking to maximize kitchen space without sacrificing performance.

One of the standout features of the JVM1790 is its 1.7 cubic feet capacity, which provides ample room for larger dishes and multiple cooking needs. The microwave is equipped with 950 watts of cooking power, ensuring food is prepared quickly and evenly. This microwave also features a range of power levels, allowing users to select the ideal power intensity for various cooking tasks.

The JVM1790 is designed with convenience in mind. It includes a convenient turntable that helps to circulate heat evenly, ensuring thorough cooking. The microwave also offers a variety of pre-programmed cooking options, which simplify the cooking process. Users can easily prepare popcorn, defrost meat, or heat up leftover meals with just the push of a button.

In terms of technologies, the GE JVM1790 employs Sensor Cooking controls, which automatically adjust cooking times and power levels for various food types. This feature takes the guesswork out of microwave cooking, helping to achieve optimal results with minimal effort. Moreover, the model includes venting options with two-speed exhaust fans that efficiently eliminate smoke, steam, and odors from the kitchen.

Aesthetically, the JVM1790 is available in several finishes, including stainless steel, which complements modern kitchen designs. The sleek design features a hidden vent and a bright, easy-to-read display, ensuring that it not only performs well, but also adds a touch of elegance to your kitchen.

The JVM1790 also prioritizes user safety with its child lock feature, preventing accidental operation by little hands. Additionally, the built-in lighting illuminates the cooktop below, enhancing visibility during cooking or meal prep.

Overall, the GE JVM1790 offers a blend of reliable performance, modern technology, and practical design. Its combination of power, convenience features, and stylish aesthetics makes it an excellent addition to any kitchen, meeting the diverse needs of busy families and home cooks alike.