Design Guide, Installation Space, Product Clearances

Design Guide

THE INSTALLATION SPACE

	Locate
	Outlet
	10-1/2"	24"
34-1/2"-35"	9" Max.
	1-1/2"	24-1/8" Framed Models
	1-1/2"	23-3/4" Stainless Steel Models
	23-3/4" Min.	23-3/4" Stainless Steel Models
	23-3/4" Min.
	NOTE:	34-1/4"
	Handle	to 34-3/4"
	Handle

and handle standoff depth is 1-3/4″

23-3/4"

The cutout depth should be 24″

The cutout dimensions shown allow for a full door swing and access to the pull-out racks when installed as a built-in in standard 24″ deep cabinets.

•The wine chiller, wine reserve and beverage center can be installed freestanding.

•If installing between frameless cabinets, a 1/2″ wide filler strip or side panel may be needed on hinge side. The filler strip will act as a spacer between the case and adjacent cabinet door swing. The width

of the opening must include the filler panels. NOTE: The door should protrude 1″ beyond the

surrounding cabinets. Custom framed models will protrude 1-7/8″beyond surrounding cabinet doors.

Additional Specifications

•A 120 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall as shown. Electrical must be located on rear wall as shown. NOTE: GFI (ground fault interrupter) is not recommended.

PRODUCT CLEARANCES

The stainless steel wine chiller, wine reserve and beverage center is factory set for a 110° door swing. Models that accept custom panels have a 95° door swing.

When installed in a corner:

•Allow 4″ min. clearance on the hinge side for the 90° door swing and to allow racks to slide out.

•Allow 10″ minimum clearance on the hinge side for a full

110° door swing. (Models ZDWI240WII and ZDBI240WII have a 95° door swing.)

NOTE: Custom handle clearances may vary, depending on custom handle depth.

10" Minimum	90° Door Swing
to Wall
to Wall

21-5/8"

23-5/8"

90°

110°*

	4" Minimum
*95° Door Swing on Custom Frame Models	to Wall

•The door swing is reversible on all models. If desired, change the door swing before installation or before installing the custom frame panel.

Choose the location:

•These products may be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper access to the door.

•Do not install these products where the temperature will go below 55°F (13°C) or above 90°F (32°C).

•Do not install where it will be subject to direct sunlight, heat or moisture.

•These products are not designed to be stacked one over the other.

Black or Stainless Steel Toekick Options

•These products are shipped with a black toekick installed. An optional stainless steel toekick is also supplied with each product. For shipping purposes, the stainless steel toekick is secured to the back of the unit.

ZTBSS1 Tubular Handle

ZTBSS1 Monogram stainless steel tubular handle is available for models ZDWI240WII and ZDBI240WII.

SIDE-BY-SIDE INSTALLATIONS

Increase storage capacity by installing two Monogram

beverage centers, wine chillers or wine reserves together.

Locate

Outlet

Or, for a complete refreshment center, install any two

10-1/2"

14"

10-1/2" 24"

of these units together.

• A side-by-side installation requires at least a 47-1/2″

34-1/2"-35"

wide opening. No trim kits required.

15"

1-1/2"

• Products must operate from separate, properly

47-1/2" Min.

grounded receptacles.

r10279v specifications

The GE R10279V is a state-of-the-art digital multimeter that stands out in the field of electronic measurement and testing. Known for its accuracy and reliability, this device is widely used by professionals in various industries including electronics, telecommunications, and industrial maintenance.

One of the main features of the GE R10279V is its high precision measurement capability, enabling users to perform various electrical measurements with confidence. It can accurately measure AC and DC voltage, AC and DC current, resistance, frequency, and even temperature. This wide range of measurement options makes it an essential tool for troubleshooting and testing electrical systems.

Equipped with advanced technologies, the R10279V offers a smart auto-ranging function that automatically selects the best range for the measurements being taken. This feature eliminates the guesswork involved in selecting the appropriate measurement range and enhances user efficiency. Additionally, the multimeter features a robust display that provides clear, readable readings under various lighting conditions, making it easy to use in diverse working environments.

The GE R10279V is built to withstand the rigors of everyday use, showcasing a rugged and compact design. Its durable casing protects it against impacts and ensures longevity, making it suitable for fieldwork as well as laboratory settings. Moreover, the device includes safety features that comply with international standards, including CAT ratings that assure users of its ability to handle high voltage and current applications safely.

In terms of connectivity, the R10279V supports data logging capabilities, allowing users to record and store measurement data for later analysis. The device can also be interfaced with computers through USB or wireless connections, significantly streamlining data transfer and reporting processes.

Other noteworthy characteristics include its lightweight design for portability, long battery life to ensure extended operational periods, and a user-friendly interface with intuitive controls. Additionally, comprehensive manuals and customer support from GE facilitate ease of use, catering to both seasoned professionals and novices alike.

In summary, the GE R10279V digital multimeter integrates precision measurement, advanced technologies, and robust design, making it a versatile tool for electrical measurement and analysis in various applications. Its user-friendly features and reliable performance solidify its status as a preferred choice among professionals in the field.