GE ZGU384NSMSS Convert LP Gas Model ZGU384LSMSS to Natural Gas Operation

Page 17

Installation Instructions

Convert LP Gas Model ZGU384LSMSS to Natural Gas Operation

If sold outside the U.S. and Canada:

WARNING:If you wish to use this product with Liquefied Petroleum (LP) gas containing greater than 10% butane, you must purchase the butane conversion kit #WB28T10238. To order, please call 1.888.664.8403 or 1.787.276.4051.

SAFETY INFORMATION

The pressure regulator and burner orifices are set for LP gas operation.

To convert this cooktop from LP gas operation to natural gas operation, the regulator and burner orifices

1ADJUST THE REGULATOR

A.Disconnect all electrical power, at the main circuit breaker or fuse box.

B.Shut off the gas supply to the cooktop by closing the manual shut-off valve.

C.Adjust the pressure regulator by the following instructions:

Unscrew the cap.

Place your thumb against the flat side of the spring retainer and press down to remove the retainer.

Carefully look at the spring retainer to locate the NAT or LP position.

Cap Gasket

must be converted. Natural gas burner orifices are attached to the regulator.

CAUTION —The cooktop, as shipped from the factory, is set for use with its intended gas. If you wish to use your cooktop with the alternate gas, you must first replace the orifices and convert the pressure regulator.

LP

NAT

LP

NAT

NAT.

position

NAT

LP

 

Spring

NAT

retainer

LP

 

L.P./propane position

OFF FOR

DOWN

WARNING —This conversion must be performed by a qualified installer or gas supplier in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for the conversion.

CAUTION —The following adjustments must be made before turning on the burner. Failure to do so could result in serious injury. Be sure pressure regulator has been converted as described in Step 1.

TOOLS YOU WILL NEED FOR

CONVERSION

Crescent wrench

7mm nutdriver

 

Small flat-head

Safety glasses

screwdriver

(2 to 2.4 mm or

 

3/32tip size,

 

60 mm long)

17

Pressure regulator

Turn the spring retainer over so that the desired gas is showing on the bottom.

Snap the retainer back into position.

Screw the cap back onto the regulator.

2 CHANGE BURNER ORIFICES

INSTALLATION TIP: First remove all

Burner cap

orifices and then start replacing them.

 

This will help to prevent the possibility

 

that some may not be replaced.

Burner

 

A. Remove the burner grates,

 

head

 

burner caps and burner heads.

 

B. Using a 7mm nut driver, remove the

 

top burner orifices. There are two

 

orifices per burner.

 

 

Burner

The main orifice is

Spark igniter

base

located low in the center

 

 

 

of the burner, while the

Simmer

Main

simmer orifice is located

orifice

 

higher beside the center

 

orifice

of the burner.

 

 

 

 

 

Image 17
Contents La section française commence à la Questions? Call 800.GE.CARESFor Your Safety Safety InformationBefore YOU Begin What to do if YOU Smell GASElectrical Requirements ContentsTools YOU will Need For Installation Installation PreparationModels Available Parts IncludedCooktop and ZVB30 Downdraft Vent Combination Installation Installation OptionsInstallation Above Cabinet Drawers Advance PlanningPRE-INSTALLATION Checklist Dimensions and Clearances Optional Combination Installations Power Supply LocationsGas supply Rear-Burner BoxInstall the Cooktop Installation InstructionsInstall Pressure Regulator Connect ElectricalCheck igniters Assemble BURNERS, Check IgnitionBurners should be checked frequently Operation ChecklistInstallation Options ZTD910 28-1/2″ ZKD910 25-1/2″ 2″cabinet top 25″ 2″min -5/8″ 36″ Countertop 1/4″heightDim. a Ovens Dim. a Dim. B Cooktop Installation Over aModel ZET1, ZEK938 or ZET938 Adjust the Regulator Safety InformationTools YOU will Need for Conversion Change Burner OrificesTesting Flame Stability Adjust Burner Flames34SL 51SN are for all Four burnersConvert LP Gas Model ZGU384LSMSS to Natural Gas Operation Installation Instructions for LP to Natural Gas Conversion Avant DE Commencer Information de la sécuritéPour Votre Sécurité Ou de tout autre appareil ménagerContenu Information de la sécurité Avertissement DébranchezBesoins D’ÉLECTRICITÉ Modèles Disponibles Préparation à l’installationPièces Comprises Matériaux Dont Vous Pourriez Avoir BesoinInstallation au-dessus des tiroirs des armoires Options D’INSTALLATIONPlanification Avancée Kit de conversion haute altitude WB28T10185Sur la face antérieure Liste DE Vérification DE PRÉ-INSTALLATIONLe régulateur est collé Base d’armoire Dimensions ET DégagementsArrière-Enceinte du brûleur Emplacements DE L’ALIMENTATION DE GAZAlimentation de gaz Installez LE Régulateur DE Pression suite Instructions d’installationAvertissement ne réutilisez Avertissement n’utilisezVérifiez les allumeurs Avertissement allumerLes brûleurs doivent être régulièrement vérifiés Liste DE VérificationBrûleur de la Mm surface de cuisson 1/4 po Surface DE CUISSON-SPÉCIFICATIONS D’INSTALLATION Options d’installationDim. a 10,2 cm 4 po Outils Nécessaires Pour LA Conversion Renseignements SUR LA SécuritéChangez LES Orifices DES Brûleurs EncolureSi les flammes sont de Ajustez LA Flamme DU BrûleurPlus la valve qu’à sa position initiale Tester la stabilité de la flammeConvertir le modèle du gaz PL ZGU384LSMSS au gaz naturel Ajustez LA Flamme DU Brûleur GE Consumer & Industrial

ZGU384NSMSS, ZGU384L, ZGU384LSMSS, ZGU384N specifications

The GE ZGU384N, ZGU384LSMSS, ZGU384L, and ZGU384NSMSS are premium gas cooktop models that exemplify quality, performance, and modern design. Each model is tailored to meet the diverse needs of home chefs, ensuring that cooking becomes an enjoyable and efficient experience.

The GE ZGU384N is known for its robust construction and reliability. It features a durable stainless steel surface that resists stains and scratches. The cooktop includes four sealed burners that provide precise heat control, which is crucial for achieving the desired cooking results. Its continuous grates offer a seamless surface for sliding pots and pans, enhancing usability. The model's high-output burner delivers intense heat for boiling water or searing meats quickly, while lower BTU burners are perfect for simmering sauces and maintaining delicate flavors.

The ZGU384LSMSS variant boasts a sleek design with a stainless steel finish that complements a modern kitchen aesthetic. It is equipped with backlit knobs that not only provide visual appeal but also enhance functionality by indicating when the burners are on. This model features advanced technology, including electronic ignition for easy, reliable starts, and an automatic re-ignition system that ensures safety by re-lighting the burner if it goes out.

In contrast, the ZGU384L model stands out with its combination of performance and accessibility. It incorporates innovative flame recognition technology that adjusts the flame intensity based on cooking needs, ensuring efficient fuel consumption. Additionally, the model features a dishwasher-safe grates design, which makes maintenance simpler for busy households.

Lastly, the ZGU384NSMSS brings advanced cooking features to the forefront with its reversible cast iron grates, which provide versatility in cooking styles. This model integrates smart features, allowing users to monitor cooking progress through their smartphones. Equipped with high-efficiency burners, it meets the needs of those who prioritize energy conservation without compromising cooking power.

Overall, the GE ZGU384 series combines cutting-edge features, safety, and usability, making them ideal options for both novice cooks and seasoned chefs alike. Whether it's the minimalist aesthetics, powerful burners, or user-friendly technologies, these cooktops are designed to enhance any culinary adventure.