Check door balance, Toekick, Install new springs

Step 1-Turn off power and water

,Turn off power supp!g.

Turn off water supplg. Latch dishwasher door.

Step 2-!ove dishwasher

Remove the two screws securing the dishwasher to the countertop or side.

Putl the unit out from the cabinets approximatelg 10", until the door springs are exposed.

Step 5-Check door balance

WARNING:

,All dishwashers can tip when removed from enclosure,

,Injury to persons could result.

,Use caution when opening door.

,Check the door balance by opening and closing the door.

• If door drops open when released, increase spring tension. If door closes when released, decrease tension.

Step 3- Remove

__u_e_

Note: Increase or decrease tension as shown. Adjust both springs to the same tension setting to correct balance.

toekick

•Remove the screws on each side of the toekick face.

,Retain screws.

Remove the toekick from the dishwasher and set aside.

Door

Panel

Loosen 2 Screws

j"\,

Increase

Spring Tension

Hook

Over

Bracket

Tip: If door does not open easilg or fails too quicklg, check spring cable routing. The cable is held in place bg "shoulders" on the pu!leg. Check to be sure cable has not slipped over the

s-" I

s S

Decrease	Correct
Spring	i
Spring	/
Tension	/
	./

pu!leg shoulders and onto the axle.

Step a-Remove old springs

•Grasp the upper end of the spring attached to the dishwasher frame and release the hook.

,Release opposite end of the spring from the tension cable and remove the spring.

Step 7-Reinstoii toekick

Step 5-Install new springs

,Place the short end of the spring hook into the

egelet of the tension cable.

Stretch the long end of

spring and hook into the lowest notch of the frame

bracket.

•Repeat the same procedure for the opposite side.

,/
i	Hook	,
i	Over
	Bracket	,/

Correct

Incorrect

Slide dishwasher back into opening. DO NOT PUSHAGAINST FRONTPANELWITH KNEES,DAMAGEWILL OCCUR. Reinstall the 2 screws securing the dishwasher to the countertop or sides and ensure door springs do not contact water line, fill hose, wiring, etc.

• Turn water on.

, Turn electrica! power on.

		Do Not Push Against
		Front	Door Panel		With
		Knee.	Damage	to The
		Door	Panel Will	Occur.
GE Consumer & Industrial
General	Electric Compang
Louisville,	Kentuckg 40225	SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE			Pub. No. 31-30593
Louisville,	Kentuckg 40225

	DWG. NO. 206C1559P137
ge.com	05D-1297 5/05
ge.com

165D4051G009 specifications

The GE 165D4051G009 is a versatile electrical component primarily utilized in the field of automation and control systems. This device is designed to meet the rigorous demands of both industrial and commercial applications, providing reliable performance and exceptional durability. One of the standout features of the GE 165D4051G009 is its robust construction, which ensures it can withstand harsh environmental conditions commonly found in industrial settings.

The GE 165D4051G009 is equipped with advanced technologies that enhance its functionality and efficiency. One of these technologies includes the integration of cutting-edge microprocessor-based controls, allowing for improved accuracy in monitoring and control operations. This feature enables users to achieve precise control over various processes, contributing to increased productivity and reduced operational downtime.

In terms of connectivity, the GE 165D4051G009 supports a range of communication protocols, facilitating seamless integration with other automation systems. This interoperability is crucial for modern manufacturing environments where different devices must work together cohesively. The ability to communicate effectively with other components maximizes system efficiency and optimizes overall performance.

Additionally, the GE 165D4051G009 is designed with user-friendly interfaces, ensuring that operators can easily navigate and program the device. This accessibility reduces the learning curve for new users and enhances overall operational efficiency. Furthermore, the device incorporates diagnostic features that provide real-time feedback on system performance, allowing for the early identification of potential issues and reducing maintenance costs.

The characteristics of the GE 165D4051G009 also include a wide operating temperature range, enabling it to function optimally in diverse conditions. It is built to comply with various industry standards, ensuring reliability and safety in its operations. This makes it an ideal choice for applications in sectors such as manufacturing, energy, and transportation.

In summary, the GE 165D4051G009 is a highly capable electrical component known for its durability, advanced technologies, and user-friendly design. With its ability to integrate seamlessly into automation systems and its robust performance in demanding environments, it stands out as an essential solution for enhancing operational efficiency across various industries. Whether used in control systems, process automation, or other applications, the GE 165D4051G009 delivers reliability and innovation.