Samsung CE745GR service manual Output Power of Magnetron, Leakage Measuring Procedure

Page 13

Alignment and Adjustments

5-8 Output Power of Magnetron

CAUTION

MICROWAVE RADIATION

PERSONNEL SHOULD NOT ALLOW EXPOSURE TO MICROWAVE RADIATION FROM MICROWAVE GENERATOR OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.

The output power of the magnetron can be measured by performing a water temperature rise test. Equipment needed :

*Two 1-liter cylindrical borosilicate glass vessel (Outside diameter 190 mm)

*One glass thermometer with mercury column

NOTE: Check line voltage under load. Low voltage will lower the magnetron output. Make all temperature and time tests with accurate equipment.

1.Fill the one liter glass vessel with water.

2.Stir water in glass vessel with thermometer, and record glass vessel's temperature ("T1", 10±1ûC).

3.After moving the water into another glass vessel, place it in the center of the cooking tray. Set the oven to high power and operate for 51seconds exactly. (2 seconds included as a holding time of magnetron oscillation:)

4.When heating is finished, stir the water again with the thermometer and measure the temperature ("T2").

5.Subtract T1 from T2. This will give you the water temperature rise. (ΔT)

6.The output power is obtained by the following formula;

Output Power =

4.187 x 1000 x ΔT+0.88xMcx(T2-T0)

49.25: Heating Time (sec)

 

4.187 : Coefficient for Water

 

49.25

1000 : Water (cc)

 

 

 

 

ΔT : Temperature Rise (T2-T1)

 

 

Mc : Cylindrical borosilicate glass weight

 

 

To : Room temperature.

7. Normal temperature rise for this model is 9ûC to 11ûC at 'HIGH'.

NOTE 1: Variations or errors in the test procedure will cause a variance in the temperature rise. Additional power test should be made if temperature rise is marginal.

NOTE 2: Output power in watts is computed by multiplying the temperature rise (step 5) by a factor of 85 times the of centigrade temperature.

5 9 Leakage Measuring Procedure

5-9-1 Record keeping and notification after measurement

1)After adjustment and repair of a radiarion preventing device, make a repair record for the measured values, and keep the data.

2)If the radiation leakage is more than 5 mW/§† after determining that all parts are in good condition, functioning properly and the identical parts are replaced as listed in this manual notift that fact to ;

J.V.SAMSUNG SERVICE LTD. MARSHAL ZHUKOU.,1.OFFICE 201 123308,MOSCOW,RUSSIA

5-9-2 At least once a year have the microwave energy survey meter checked for accuracy by its manufacturer.

Samsung Electronics

5-3

Image 13
Contents Microwave Oven Page Safety precautions PrecautionSpecial High Voltage Precautions Special Servicing PrecautionsTable of Specifications SpecificationsComparison Chart Operating Instructions Features & External ViewsControl Panel Replacement of Magnetron, Motor Assembly and Lamp Disassembly and ReassemblyReplacement of High Voltage Transformer Removal of Door Assembly Replacement of Door AssemblyReplacement of Drive Motor Replacement of FuseRemoval of Control Box Assembly Replacement of Control Circuit BoardHigh Voltage Transformer Alignment and AdjustmentsLow Voltage Transformer MagnetronPrecaution Main Relay and Power Control RelayHigh Voltage Capacitor High Voltage DiodeLeakage Measuring Procedure Output Power of MagnetronMicrowave Heat Distribution Heat Evenness Electrical Malfunction TroubleshootingTroubleshooting Exploded Views Exploded Views and Parts ListParts No Description/Specification Qty Remarks Main Parts ListBody Latch Parts List Control Parts ListDescription/Specification Qty Parts No Description/Specification Qty Remarks Old Parts NoStandard Parts List P.C.B Diagrams C.B DiagramsParts No Description / Specification Qty Remarks P.C.B Parts ListSchematic Diagrams Schematic Diagrams