Fisher & Paykel OR90SDBGFPX Electrical, Power supply 220-240V~ 3450W 50Hz 15A

Page 5

Safety and warnings

3

Electrical

This cooker is to be installed and connected to the electricity supply only by an authorised person. If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the electrical system is suitable for the electricity drawn by the cooker.

The appliance must be connected to the mains electricity supply, checking that the voltage corresponds to the value given in the rating plate and that the electrical cable sections can withstand the load specified on the plate.

A suitable disconnection switch must be incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. The switch must be of an approved type installed in the fixed wiring and provide a 3 mm air gap contact separation in all

poles in accordance with the local wiring rules.

In Australia and New Zealand, a switch of the approved type with a 3 mm air gap must be installed in the active (phase) conductor of the fixed wiring.

The switch must always be accessible.

The power supply cable must not touch any hot parts and must be positioned so that it does not exceed 75 OC at any point.

To connect the cooker to the mains electricity supply, do not use adapters, reducers or branching devices as they can cause overheating and burning.

This cooker must be connected to a suitable double pole control unit adjacent to the cooker. No diversity can be applied to this control unit.

If the electrical supply cord is damaged, it must only be replaced by an authorised person. This cooker must be connected to electrical supply using V105 insulated cable.

The cooker must be earthed.

Power supply

220-240V~ 3450W 50Hz - 15A (230V)

Image 5

Contents Installation instructions Page Contents General Safety and warningsInstallation Electrical Power supply 220-240V~ 3450W 50Hz 15AOperation Important safety instructions Important safety instructions Important safety instructions Dimensions and clearances Installation instructionsOverhead Clearances Rear and Side ClearancesLocating the area for gas and electrical connection Cooker overall dimensions mmScrew/unscrew the feet to get the required height Levelling the cookerSupplied must be fitted according to Instructions below Fitting the anti-tilt bracketFixing the backguard Moving the cookerInstallation with a flexible hose assembly Connecting the cooker to the gas supplyFitting the brass conical adaptor LPGAdjusting the minimum burner setting Leak-testing and flame-testing the cookerConverting to a different gas type Replacing the injectorsInner crown Outer crown InjectorInjector for Injectors for Semi-rapid and triple-ring burners Adjusting the minimum burner settingInside crown of dual burner Outside crown of dual burnerLPG CI G SI C SE Page Control panel OR90SDBGFPX First useButtons Illuminated symbolsTo set the clock To change the timeBefore using your new oven, please Using your ovenGuard rail StopSelect a function 225CWhen you have finished cooking When the oven is preheating and during cooking4a To check the set temperature 4b To check the time of dayThis is not a cooking function Cooking functionsSelf Clean Cooking Guide Cooking guideChanging the oven from Celsius to Fahrenheit Food Shelves Recommended Secure the meat Using the rotisseriePrepare the rotisserie supports Rotisserie drive hole To set the timer Using the electronic timerTo cancel the timer When the time is upTo set the oven for automatic cooking Automatic cookingGas burners Using your gas cooktopSemi-rapid and triple-ring wok burners Dual burnerFlame failure safety feature Before using your cooktopUsing the gas burners If the flame is irregular If a burner does not lightWok stand Matching cookware to burnerDiameters of pans which may be used on the cooktop General advice Care and cleaningCleaning the outside of the cooker Cleaning the gas cooktopReplacing the semi-rapid burners Burner parts and pan supportsCorrect positioning of flame spreader dual burner Replacing the triple-ring wok and dual burnersRefitting the side racks Cleaning the inside of your ovenRemoving the side racks Cleaning the grill tray and shelves Cleaning the enamel cavityGuard rail StopFitting the sliding shelf supports Fitting and removing the sliding shelf supportsReplace the drawer Storage DrawerTo remove the drawer Replacing the oven light bulbs Removing and replacing the door glass panes for cleaning Removing the door Remove the inner and middle glass panes When replacing the glass panes, make sure that After cleaning, replace the glass panesAngle-cut corner Glass retainer Hold the door firmly Refit the doorSensor Door Lock Using the Self Clean function To start a Self Clean cycle Using the Self Clean functionPress the button the P will go out To cancel a Self Clean cycleTroubleshooting Removing the door for cleaning Do a test Self Clean afterReplaced the door after cleaning Display shows FdorProduct details Warranty and serviceBefore you call for service or assistance Page Page NZ AU