Thermador PHH30DS, PHH36DS manual Wall Mount Installation, Cabinet Installation, Side slot x

Page 10

Wall Mount Installation

Note: see below if cabinet installation is preferred

4.After the hood installation height has been determined draw a horizontal line at a distance above the cooktop equal to the desired hood installation height plus 7- 1/ 2”. See also Figure 6a.

5.Find the centerline of the cooktop.

Draw a vertical line along this centerline up to the horizontal line drawn in step 1 and draw a vertical line right and left at a distance of 12-5/8”to determine the mounting location of the mounting hooks shipped with the hood.

6.Fit two mounting hooks on the wall to hang the hood through the provided slots (2 wall anchors+2 hooks + 2 screws 5x35).

7.Run 8” Duct , long enough to reach the transition once the hood has been installed plus 1 1/2” inch to connect ductwork.

Fix Duct to transition with screws and seal with tape.

8.Remove 1 of 2 knockouts and install 1/2” conduit connector in j-box.

9.Hang the hood and adjust its position through the screws on the hooks.

10.Fix the hood to 4 additional point,2 on upper side, 2 on lower side (use 4 wall anchors + 4 washers + 4 screws 5x35.

11.Vertical discharge

Cabinet Installation:

Note: see above if wall mount installation is preferred

Note: distances on Table 3.

4.Find the centerline of the cabinet bottom. Draw a line along this centerline from rear to front of the cabinet.

5.Draw two lines, one at a K distance from the wall, the other one at a Z distance from the previous line.

Mark 4 points , two along each line at a distance of half W from the center line, to determine the screw locations.

6.Fit 4 screws on cabinet bottom do not tighten completely but leave a space of about 1/2” from cabinet bottom surface and head screws.

7.Run 8” Duct , long enough to reach the transition once the hood has been installed plus 1 1/2” inch for connect ductwork.

8.Remove 1 of 2 knockouts and install 1/2” conduit connector in j-box.

9.Hang the hood on screws through side slots provided on hood top.

Tighten the four screws.

Note: If possible fix the hood on the wall at 4 additional point (2 on upper side, 2 on lower

side).

10.From the inside of the cabinet attach the transition on upper outlet (vertical discharge - see also „Assembly of the 8” Transition“ on previous pages)

HOOD WIDTH

DIM. "W"

DIM. "K"

DIM. "Z"

30"

29 - 1/8"

2 - 1/2"

7 - 1/16"

36"

35 - 1/16"

2 - 1/2"

7 - 1/16"

 

 

 

 

 

 

 

 

Table 3

 

 

Side slot x 4

Knockouts

 

 

Z

(junction

 

 

box)

W

Top

K

 

 

 

 

 

outlet

Top

 

 

 

 

 

 

screw

 

 

 

location

Top

 

Rear

 

 

outlet

 

screw

 

 

 

location

 

 

 

 

 

 

Square

 

 

 

slot

7 1/2"

 

bottom fixing

 

 

 

 

screws locations

Figure 6a

W

CL

Z

 

 

K

 

Hook for wall

 

Screw for

 

installation

 

cabinet

 

25 3/16"

bottom

 

 

 

installation

7 1/2"

12 5/8"

12 5/8"

Adjusting

 

 

screw

 

 

 

 

CL Bottom of the Hood

Figure 6b

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Ventilation Page To Reduce the Risk of FIRE, USE only Metal Duct Work Read All Instructions Before Using the ApplianceOperation Electrical requirements Parts Included with your Hood Installing the HoodOptional accessory Parts Not Included with your HoodDucting Typical installationChoose vent options Recirculating Vertical discharge Horizontal dischargeTotal of both columns= Ductwork Installation Guidelines After having choosen the vent optionKeyhole Assembly of the 8 TransitionDischarge Direction PinCabinet Installation Wall Mount InstallationSide slot x For both installation method Failure to do so can result in death or electrical shockPage Avertissement Mode OpératoireAvertissement Lire Toutes les Instructions Avant d’Utiliser l’Appareil Spécifications électriquesÉléments compris avec votre hotte Installation DE LA HotteAccessoires en option Éléments non compris avec votre hotteConduits Installation classiqueRecyclage d’air Évacuation verticale Évacuation horizontale 10 po TABLEAU2.RECOMMANDATIONSPOURL’INSTALLATIONDESCONDUITS Après avoir choisi le type d’évacuationAttacher le raccord de Direction d’évacuationPour changer pour une évacuation Évacuation verticale Uniquement Ne pasInstallation au mur Installation encastréeÉtapes finales d’installation Pour les 2 types d’installationsTube de courant électrique De la boîte à fusibles Leer LAS Instrucciones Antes DEL USO Advertencia AdvertenciaFuncionamiento Leer Todas las Instrucciones Antes de Usar el Aparato Requisitos eléctricosPartes Incluidas con la Campana Accessorios opcionalesInstalar LA Campana Herramientas necesariasEscoger las opciones de ventilación Instalación típicaConducto Total de ambas columnas= Después de haber escogido la opción de ventilación FiguraMontaje de la Transición Dirección de la descarga¡ADVERTENCIA Con descargue vertical no instalar laInstalación en el el fondo del Instalación en la paredGabinete Instrucciones DE Conexión Eléctrica Para ambos métodos de instalaciónConexión eléctrica Últimos pasos para la instalaciónLI2W2A

PHH36DS, PHH30DS specifications

Thermador has long been at the forefront of luxury kitchen appliances, and their PHH30DS and PHH36DS hoods exemplify this legacy. Designed to combine powerful performance with beautiful aesthetics, these hoods are perfect for the discerning chef and homeowner alike.

One of the standout features of both the PHH30DS and PHH36DS is their impressive ventilation capabilities. With a powerful blower system, these hoods effectively eliminate smoke, steam, and odors from your kitchen, ensuring a pleasant cooking environment. They boast a CFM rating that can be adjusted for optimal performance, catering to various cooking styles and needs.

Both models also highlight Thermador's patented Star® Filter technology. This unique design enhances the airflow efficiency and ensures that grease and other particulates are captured effectively. The filters are dishwasher-safe, making maintenance and cleanliness convenient for everyday use.

The PHH series features elegant stainless steel construction that adds a modern touch to any kitchen. Its sleek design can complement various kitchen aesthetics, making it a versatile option for homeowners looking to elevate their culinary space. The hood is available in both 30-inch and 36-inch widths, catering to different kitchen configurations.

An intuitive control panel enhances usability. The hoods come with backlit push-to-open controls that allow for effortless operation, even during cooking. Additionally, the LED lights provide ample illumination over the cooking surface, enabling you to monitor your culinary creations with ease.

Another noteworthy characteristic of the PHH30DS and PHH36DS is their quiet operation. Thermador has engineered these hoods to minimize noise levels while still providing powerful suction. This means that you can enjoy a serene environment without the distracting hum often associated with kitchen ventilation.

Furthermore, both models feature a luxurious design with a low-profile appearance, allowing them to blend seamlessly into the kitchen. The hoods also include a telescoping chimney, accommodating various ceiling heights and enhancing installation flexibility.

In summary, the Thermador PHH30DS and PHH36DS hoods are excellent choices for anyone looking to invest in high-quality kitchen ventilation. With their powerful performance, advanced filtration technology, user-friendly controls, and elegant design, these hoods exemplify the blend of functionality and style that Thermador is known for.
Top Page Image Contents