Product Dimensions

ZIC360NX

GE Monogram® 36" Built-In Side-by-Side Refrigerator

Dimensions and Installation Information (in inches)

Door Swing Clearances

The Installation Space

The finished cutout width must be 35-1/2".

35-1/2"

Finished Width

2-5/16"

Wall View

The installation must allow for clearances to adjacent walls or cabinets. These refrigerators are equipped with a 2-position door stop. The factory-set 130° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.

84-1/2" max

83-1/2" min

Finished

Opening

10" Electrical

Area

24" Cutout Depth

5"	Cold Water			5"
		Supply


3 1/2"			3 1/2"

75" From Floor to Bottom of Electrical Area

Note: Icemaker water connectio is at the front.

130° Door Swing

25" Min. to

Wall

23-7/8"

90° Door Swing Behind Frame

36-3/4"

The cutout depth must be 24"

The refrigerator will project forward, slightly beyond adjacent cabinetry, depending on your installation.

The cutout depth beneath a soffit

130°

90°

4" Min. to Wall 5" Min. for Professional Models

When installed beneath a soffit, the soffit cannot exceed the 24" installation depth shown. The top case trim overlaps the bottom of the soffit.

Electrical

A 115V, 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

Water Line

All models are equipped with an automatic icemaker. The water line can enter the opening through the floor or back wall. Route GE SmartConnect™ Kit or 1/4" O.D. copper tubing between the cold water line and the water connection location at the front of the refrigerator. The installation of an easily accessible shut-off valve in the water line is required.

35"	Case Depth:
Case Width	25-3/8" Framed Models
	25-3/4" Stainless Steel Models

Allow 25" minimum clearances for a full 130° door swing. Allow 15" for pan removal.

•4" minimum clearance is required when the door swing is adjusted to 90°. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.

•See door swing illustrations to determine interaction with adjacent cabinets or countertops.

ZUG2, ZUGSS2 Unified Grille Panel Kit

•If you are installing two refrigerators side by side, the installation space must be 71-1/2" wide.

Note: Additional cutout width may be required when side panels are used. Add side panel thickness to the finished cutout to calculate rough-in width.

•The water and electrical locations for each product must be located as shown.

•A separate 115V, 60Hz., 15 or 20 amp power supply is recommended for each product.

71-1/2" Finished Width

*83-1/2"	*84" From
*83-1/2"	Floor to
at	Top Frame
Rear
	36"
	Frame to Frame Width

Depth Including Handles:

26-7/8" Framed Models

27-3/4" Stainless Steel Models

*Shipping Height. The refrigerator can be adjusted to fit into a cutout that is 83-1/2" min. to 84-1/2" max. height. The top case trim at the front is 1/2" higher and will overlap upper cabinetry or soffit. Use leveling legs and wheels for a maximum 1" height adjustment.

2-5/16"Electrical

10"

84-1/2" max 24" Cutout

83-1/2" min Depth Finished

Opening

5" Water Supply

24-3/16"

Wall View

10"

75" From

Floor to Bottom

of Electrical

Water Supply

Area

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.

26"

3-1/2"

26"

3-1/2"

Listed by Underwriters Laboratories

Specification Created 6/08

110112

ZIC360NX specifications

The GE ZIC360NX is an advanced industrial automation solution designed to enhance operational efficiency and drive productivity within various sectors. This innovative equipment stands out for its robust features, state-of-the-art technologies, and highly customizable characteristics, making it a preferred choice for many businesses looking to modernize their processes.

One of the most notable features of the ZIC360NX is its high-performance control system. It combines a powerful processing unit with advanced software algorithms that enable real-time data analysis and rapid response to operational demands. This capability allows manufacturers to monitor and optimize their processes continuously, leading to reduced downtime and increased throughput.

The ZIC360NX incorporates cutting-edge connectivity options, supporting industry-standard protocols such as OPC UA, MQTT, and RESTful APIs. This feature ensures seamless integration with existing systems and enables easy communication between equipment, sensors, and cloud platforms. The emphasis on interconnectivity boosts data visibility and allows companies to implement predictive maintenance and more effective resource allocation strategies.

In addition to its connectivity, the ZIC360NX also supports a wide range of input and output options, making it suitable for various applications. Its modular design allows users to tailor configurations to meet specific operational needs, ensuring flexibility as business requirements evolve. This adaptability extends to its compatibility with various types of sensors, actuators, and other field devices, ensuring it can handle diverse industrial environments.

Security is a top priority with the GE ZIC360NX. It incorporates advanced cybersecurity features to protect against potential threats while ensuring compliance with industry regulations. This reinforcement of security protocols safeguards sensitive data and helps maintain operational integrity in today's increasingly interconnected world.

User-friendliness is another hallmark of the ZIC360NX. The intuitive interface simplifies navigation and allows operators to easily access critical information and analytics. Training time is minimized, and workforce efficiency is maximized, enabling faster decision-making on the production floor.

In conclusion, the GE ZIC360NX represents a significant advancement in industrial automation technology. Its high-performance capabilities, extensive connectivity, security measures, and user-friendly interface make it an invaluable tool for any organization aiming to streamline operations and enhance productivity in a rapidly evolving marketplace. Its versatile characteristics cater to diverse application needs, positioning the ZIC360NX as a leader in the industrial automation space.