Philips MC-200 manual CD Operation, Selecting a different track, Playing a disc

Page 12

CD Operation

English

 

 

CD

PROGRAM

STANDBY

 

PROGRAM

 

ON

 

 

 

 

 

 

 

 

TIMER

SELECT

 

 

 

ON • OFF

SOURCE

 

 

 

 

DBB

DSC

INCREDIBLE SURR.

 

INTERACTIVE SOUND

 

 

 

 

 

 

VOLUME

iR SENSOR

STOP

PRESET

PLAY•PAUSE

RDS

 

 

 

 

 

CLOCK

REPEAT

TUNING

RECORD

TUNING

SHUFFLE

REV MODE

 

 

 

SIDE A/B

BAND

 

 

 

 

 

PREV

 

NEXT

 

IMPORTANT!

The lens of the CD player should never be touched.

X

5To interrupt playback press PLAY•PAUSE 2; (on the remote control 2;). Press PLAY•PAUSE 2; (on the remote control 2;) again to resume play.

The display freezes and the elapsed playing time flashes when playback is interrupted.

6To stop disc playback, press STOP 9.

Note: CD play will also stop when;

– the CD door is opened.

– the disc has reached the end.

– you select another source:TAPE,TUNER or AUX.

Selecting a different track

Press PREV ¡1 or NEXT 2™ (on the remote control ¡ or ™) once or repeatedly until the desired track number appears in the display.

If you have selected a track number shortly after loading a disc or in the PAUSE position, you will need to press PLAY•PAUSE 2; (on the remote control 2;) to start playback.

Playing a disc

This CD player plays Audio Discs including CD- Recordables and CD-Rewritables.

CD-ROM, CD-I, CDV, VCD, DVD or computer CDs, however, are not possible.

Finding a passage within a track

1

Press and hold down on PREV ¡1 or

 

NEXT 2™ (on the remote control à or á ).

 

The disc is played at high speed and low

 

volume.

2

When you recognise the passage you want,

1Select CD source.

2Press OPEN•CLOSE on the top of the system to open the CD compartment.

OPEN is displayed when you open the CD compartment.

OPEN • CLOSE

release PREV ¡1 or NEXT 2™ (on the

remote control à or á ).

Normal playback continues.

Note:

– During a disc programme or if SHUFFLE/

REPEAT active, searching is only possible within the

same track.

3Insert a disc with the printed side facing up and press down on OPEN•CLOSE to close the CD door.

READ is displayed as the CD player scans the contents of a disc, and then the total number of tracks and playing time are shown.

4Press PLAY•PAUSE 2; (on the remote control 2;) to start playback.

Current track number and elapsed playing time of the track are displayed during disc playback.

12

pg 001-022/MC200/22-Eng

12

10/5/01, 4:25 PM 3140 115 28691

Image 12 Contents
200 How to connect a plug Important notes for users in the U.KMains plug Copyright in the U.K3140 115 Klass 1 laseraparat Luokan 1 laserlaiteIndex Contents Supplied accessories Safety InformationGeneral Information Environmental InformationFor optimal performance, use only the original power cable PreparationsRear connections Type plate is located at the rear of the systemInserting batteries into the remote control Connecting other equipment to your systemOptional connection FM AntennaControls on the system and remote control Switching the system on Adjusting volume and soundPower-saving automatic standby Preparation proceduresCD Operation Selecting a different trackPlaying a disc Finding a passage within a trackDifferent play modes Shuffle and Repeat Programming track numbersReviewing the programme Erasing the programmeTuning to radio stations Radio ReceptionProgramming radio stations Automatic programmingTuning to preset radio stations Searching programme type PTYScrolling through different RDS information RDS Programme typesRDS News and Traffic Announcement TADisarming RDS News and Traffic Announcement Switching tape sides Reverse mode optionsTape Operation / Recording Tape playbackRecording timer Press Timer Onoff againClock digits for the minutes flash Clock/Timer Setting the timerSetting the clock Activating and deactivatingSpecifications Subject to modificationMaintenance TroubleshootingProblem Solution B CRadio Reception Tape Operation / RecordingGeneral
Related manuals
Manual 22 pages 56.5 Kb