Amana W10310515A warranty Select Options, Select a Cycle, Start or Resume a Cycle, To turn on Lock

■ Rinse aid keeps water from forming droplets that can	Full
dry as spots or streaks. They also improve drying by
allowing water to drain off of the dishes after the final
rinse.
■ Rinse aid helps to reduce excess moisture on the	Add
dish racks and interior of your dishwasher.

■Check the rinse aid indicator. Add rinse aid when indicator drops to “Add” level or, when rinse aid indicator looks light. A light visual indicator means to add rinse aid, and a dark visual indicator means that there is sufficient rinse aid in the dishwasher.

■ Dispenser with one lid - To add			Lock
rinse aid, turn the dispenser
cap to “Refill” and lift off. Pour			-	-	5
rinse aid into the opening until
			-
							3
							4
the indicator level is at “Full.”		-max	fill					1	¹⁄₄ turn
								2
Replace the dispenser cap and	Refill								to lock
		-
turn to “Lock.” Make sure cap		-				--
			-					-
is fully locked.			-	-	-

Select Options

You can customize your cycles by pressing the options desired.

Hi-Temp Wash – (use only with Heavy and Normal wash cycles) heats the water during the wash portions of the cycle.

Heated Dry – (automatic with all except rinse cycle) use for best drying results. Turn off by pressing HEATED DRY so that the light goes off.

4-Hour Delay – (any cycle) offers the choice to start the dishwasher automatically at a later time. Select a wash cycle and options. Press START/RESUME. Close the door firmly.

Locked – (on 4-Hour Delay button) use to avoid unintended use of your dishwasher. When Control Lock

is lit, all buttons are disabled. The dishwasher door can be opened while the controls are locked.

To turn on Lock:

or

■Dispenser with two lids - To add rinse aid, press the cover release button to open the cover. Fill the dispenser with rinse aid up to the dotted line. Close the cover.

NOTE: For most water conditions, the factory setting of 2 will give good results. If you have hard water or notice rings or spots, try a higher setting. Turn the arrow adjuster inside the dispenser by either using your fingers or inserting

aflat-blade screwdriver into the center of the arrow and turning.

STEP 3

Select a Cycle

A

A. Cover release button

	-	-	6	5	4
	-
	fill
max					3
						2
-						1
-
-						-
-
	-				-
		-	-	- -
	-

Press and hold 4-HOUR DELAY for 3 seconds. The Locked light glows. If you press any pad while your dishwasher is locked, the light flashes 3 times.

To turn off Lock:

Press and hold 4-HOUR DELAY for 3 seconds. The Control Lock light turns off.

STEP 4

Start or Resume a Cycle

■Run hot water at the sink nearest your dishwasher until the water is hot. Turn off water.

■ Push door firmly closed. The door latches automatically. Select the wash cycle and options desired OR press START/RESUME to repeat the same cycle and options as in the previous wash cycle.

■You can add an item anytime before the main wash starts. Open the door slowly and add the item. Close the door firmly. Press START/RESUME.

■Cycle status indicators allow you to follow the

progress of your dishwasher cycle. Clean indicator glows when the cycle is finished.

NOTE: Heavier cycles and options affect cycle length. Some cycles and options will take up to 3¹⁄₂ hours to complete.

Heavy – Use for heavily soiled, hard-to- clean items.

Normal – Use for normal food soil. The energy usage label is based on this cycle.

1-Hour Wash – Use for lightly soiled items. For fast results, 1-Hour Wash will clean using slightly more water and energy.

4