Child Lock, Salt Indicator, Rinse Aid Indicator

Press Start / Pause / Cancel button first to switch your machine into pause mode if you want to make any changes in the program or function while the Delay function is on. You will observe that the countdown is paused. Select programs and/or add functions you desire. Resume the delay phase and the countdown from the point they were paused, by pressing Start / Pause / Cancel button.

Press Start / Pause / Cancel button for three seconds if you want to make any cancellation while the machine is in Delay mode. Release the button when the Start / Pause / Cancel light and the ” “ display on the program display start flashing. The machine will process the necessary operations required for cancellation for a couple of minutes. The delay is cancelled when the Start / Pause / Cancel indicator light goes off and "End" (10 d) lights on the program follow-up display. You may select and operate a new program after cancellation process is over.

Press Start / Pause / Cancel button first to switch your machine into pause mode if you want to adjust a new time setting for the delay while the Delay function is on. Set the desired time by pressing (+) or (-) buttons. Start the delay countdown for the new time you have fixed by pressing Start / Pause / Cancel button again.

Child Lock

Press programe selection and half load buttons at the same time for three seconds to activate the child lock. Child lock indicator appears on the screen. Repeat the same step to deactivate the child lock. Child lock does not lock the door of the machine; rather it prevents changing the selected program or functions and deactivates Start / Pause / Cancel button.

Salt Indicator

Please check the salt indicator (17) on the display to see whether there is enough softening salt in your machine or not. You must refill the salt container when the salt indicator comes on. If the water hardness level is stored as (r1), salt indicator will never come on even if the salt container is empty. (Adjusting the water hardness level is explained in “Softening the Water” section.)

Rinse Aid Indicator

Please check the rinse aid indicator (15) on the display to see whether there is enough rinse aid in your machine or not. You must refill the rinse aid container when the rinse aid indicator comes on.

If the Rinse Aid Indicator is set to (OFF), rinse aid indicator will never come on even if the rinse aid container is empty.

Rinse Aid Indicator Setting

·When your machine is switched off, press Half Load button (2) and then On / Off button (8) to switch it on.

·Hold Half Load button (2) pressed and release On / Off button (8).

·Keep Half Load button (2) pressed for three seconds.Rinse Aid Indicator (15) comes on and the stored rinse aid indicator status of your machine appears on the display in the format of "ON" or "OFF".

·You can change the status of the indicator as "ON" or "OFF" with Start / Pause / Cancel button (1). If you switch off the machine with "On/Off" button when the status is "ON", then the rinse aid indicator will come on when the rinse aid level in your machine becomes low while the machine is in use. If you switch off the machine with "On/Off" button when the status is "OFF", then the rinse aid indicator will never come on.

Cancelling a Programme

Press Start / Pause / Cancel button for three seconds to cancel a program while it is operating. Release the button when the Start / Pause / Cancel indicator lights, at the right of the Start / Pause / Cancel button and the program display start flashing. The machine will process the necessary operations required for cancellation for a couple of minutes. The program is cancelled when the Start / Pause / Cancel indicator light goes off and "End"(10 d) lights on the program follow-up display. You may select and operate a new program after program cancellation process is over. There might be residues of detergent or rinse agent left in the machine and/on the pieces being washed depending on the step the previous program was in at the time of cancellation.

Changing the Programme

Press Start / Pause / Cancel button first to switch your machine into pause mode if you want to change your selection after you started the program. Then, come to the program you like by pressing Program Selection button. Start the new program by pressing Start / Pause / Cancel button again. Your new selection will resume operation from the step in the previous program (For example, if the previous program was in rinsing step, the new one will also start from the rinsing step). If you want to run the newly selected program from the very beginning, you have to apply the cancellation process first and then select a new program.