Liebherr HCS, 7081 411-01 manual IceMaker, Safety Instructions and Warnings, Bleeding the Ice Maker

Page 20

IceMaker

Safety Instructions and Warnings

•The Ice Maker is designed exclusively to make ice cubes in quantities needed by a household and may only be operated with water appropri- ate for this purpose.

•All repairs and work on the Ice Maker may only be done by customer service personnel or other appropriately trained personnel.

•Do not consume or use the first three batches of ice. This applies both to using the appliance for the first time and also using it after it has not been used for a long period of time.

•The manufacturer cannot accept liability for damage caused by equipment or water lines between the solenoid valve and the water supply.

•The Ice Maker will only work if the combined refrigerator-freezer is connected to the electrical outlet. It will only make ice cubes if the freezer compartment is operating.

•The Ice Maker can only make ice cubes if the upper freezer drawer is completely closed and the ice cube bin is installed correctly (Figure 17).

Bleeding the Ice Maker

IMPORTANT

To ensure a proper function of the Ice Maker the water pipe system must be purged of any air.

•Turn the Ice Maker on by touching the Ice Maker icon (Figure 21).

•Open the top freezer drawer.

•Press the button on the Ice Maker housing (Figure 19) for approx. 3 seconds. The LED above the button starts blinking.

•Press the button again briefly. The LED blinks faster.

•Close the top freezer drawer immediately.

The water intake of the appliance opens for 25 seconds and bleeds all air from the pipe system.

•After this the Ice Maker tray (Figure 20) must be emptied. Refer to chapter “Ice Maker at vacations”.

•Finally clean the ice cube bin (Figure 17).

To Start the Ice Maker

To turn the Ice Maker on

•Touch the Ice Maker icon so the Ice Maker LED comes on (Figure 21).

After you start the Ice Maker for the first time it may take up to 24 hours before the first ice cubes are ready.

Note

The first three batches of ice must not be consumed or used.

The production capacity is 100 - 120 ice cubes in 24 hours at a temperature of 0°F inside the freezer compartment.

To have the maximum capacity of approx. 150 ice cubes in 24 hours, activate the Superfrost function.

Be aware that this increases the energy con- sumption because the compressor will run con- stantly.

The ice cubes fall out of the Ice Maker into the ice cube bin (Figure 17). When the ice reaches a cer- tain level in the bin, the appliance stops producing ice automatically.The ice maker will not fill the bin to the top.

To turn the Ice Maker off

If you do not need any ice cubes, the Ice Maker can be turned off independently of the freezer com- partment.

•Touch the Ice Maker icon so the Ice Maker LED goes out.

Note

The Ice Maker can also be turned on and off by pressing the “On/Off” button at the Ice Maker housing for approximately 1 second (Figure 19).

Figure 19

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Use and Care Manual Additional benefits Table of Contents Safety Electrical SafetyPlease read and follow these instructions Disposal of Old ApplianceImportant Safety Information Safety Regulations Disposal of CartonInstalling the Water Filter Water FilterWater Filter Figure Removing the Water Filter FigureFeatures Description of appliance and equipment FigureDescription of Refrigerator Description of FreezerTemperature and control display Operating and Control Elements , FigureAppliance Operating icons Control iconsSetting the Temperature Figure To reduce the temperatureTo increase the temperature OperationPower Failure/Frost-Control Temperature Display FigureAudible alarm signal Figure Setup Mode Figure How to activate the setup modeExit setup mode Supercool Figure= Sabbath Mode How to activate the Sabbath ModeHow to deactivate the Sabbath Mode How to activate the door gasket heating= Temperature display mode How to change the temperature display to degrees CelsiusHow to adjust the water quantity = Water quantity for Ice cube tray= Drop symbol reset How to reset the drop symbolHow to activate the childproof lock How to deactivate the childproof lockTo install the vegetable drawer Refrigerator CompartmentArranging Food Figure Shelf Arrangement Repositioning the door racks FigureRemoving the shelves Figure Interior LightRepositioning the shelves Figure Freezing Freezer CompartmentFreezer compartment description Freezing with Superfrost Figure Freezing and StorageSafety Instructions and Warnings IceMakerBleeding the Ice Maker To Start the Ice MakerHow to activate the Ice Maker Vacation State Ice Maker at vacationsCleaning CleaningVacation Tips Defrosting/VacationDefrosting Troubleshooting Problem Possible Cause and RemedyIceMaker Troubleshooting Customer Service FigureService Number 2 and Appliance / serial number Appliance InformationWarranty LIEBHERR WARRANTY PLAN

CS, HC, 7081 411-01, HCS specifications

The Liebherr HCS 7081 411-01 is a cutting-edge model within Liebherr's established line of heavy lifting equipment, renowned for its robust performance and advanced technologies. Designed for versatility and efficiency, this machine caters to diverse construction and industrial applications.

One of the standout features of the HCS 7081 is its impressive lifting capacity, which allows for heavy loads to be handled with precision and ease. This model incorporates a powerful hydraulic system that ensures optimal performance even under demanding conditions. The intelligent design of the hydraulic components maximizes power while reducing energy consumption, making it an environmentally friendly choice for modern construction needs.

The HCS 7081 is equipped with advanced control systems, providing operators with enhanced functionality and safety features. The intuitive interface simplifies operation, allowing for smoother controls and improved accuracy when maneuvering heavy loads. The system also integrates real-time monitoring capabilities, giving operators instant feedback on performance metrics such as load weight and handling conditions.

Safety is paramount in the design of the HCS 7081. It features multiple redundancy systems that protect against operational failures. This model includes a slew of safety devices, such as overload protection, emergency stop buttons, and automatic limit switches that prevent unsafe operations. Liebherr’s commitment to safety ensures operators can work with confidence, knowing that their equipment is designed to minimize risks.

The HCS 7081 also boasts exceptional mobility, facilitating easy transportation between job sites. Its all-terrain capability allows it to navigate various environments, making it ideal for both urban and remote locations. The machine's compact design does not compromise on power or stability, ensuring reliable performance regardless of the operating conditions.

Another noteworthy characteristic is its durability. Constructed with high-quality materials, the HCS 7081 is built to withstand the rigors of demanding job sites. Liebherr’s reputation for excellence in engineering is evident in the machine’s robust frame and components, ensuring longevity and reliability even in the toughest environments.

In summary, the Liebherr HCS 7081 411-01 presents a fusion of power, efficiency, and safety features that set a standard in the heavy lifting equipment sector. With its advanced technologies, operator-friendly controls, and strong build quality, it stands out as an invaluable asset for any construction or industrial operation.
Top Page Image Contents