Liebherr HCS 20 installation instructions Installation Guidelines

Page 3

INSTALLATION GUIDELINES

Area Requirements

Verify the following:

•Floors can support refrigerator’s weight plus approximately 1200 pounds (544 kg) of food weight.

•Finished kitchen floor height is level. Refrigerator must be shimmed level if the floor heights

are not equal to make sure air vents are not obstructed.

•Remove anything attached to rear or side walls that can obstruct refrigerator opening.

•Cutout dimensions are accurate.

•Electrical outlet is in correct location.

Do not install this refrigerator-freezer next to any other refrigerator. Installing this refrigerator-freezer next to any other refrigerator or freezer can cause condensation or cause damage to the appliance.

Electrical Requirement

If codes require a separate grounding circuit to be used, have a qualified electrician install the circuit.

Do not ground to a gas pipe. Check with a qualified electrician if you are not sure the appliance is properly grounded. Do not have a fuse in the neutral or grounding circuit.

ELECTRICAL SHOCK HAZARD

•Electrically ground refrigerator.

•Do not use an extension cord.

•Failure to follow these instructions could result in fire or electrical shock.

ELECTROCUTION HAZARD

Electrical Grounding Required. This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible shock hazards.

•DO NOT remove the round grounding prong from the plug.

•DO NOT use a two-prong grounding adapter.

•DO NOT use an extension cord to connect power to the unit.

To protect the refrigerator from possible damage, allow the appliance to stand 1/2 to 1 hour in place before turning the electricity on. This allows the refrigerant and system lubrication to reach equilibrium.

Customer’s Responsibility

A 115 Volt, 60 Hz, 15 Amp fused electrical supply is required. We recommend using a dedicated circuit for this appliance to prevent electrical overload. Follow the National Electrical Code and local codes and ordinances when installing the receptacle.

Blocking For Safety

The anti-tip bracket must be installed to prevent the unit from tipping after it is installed. Refer to Blocking For Safety.

Unit Venting

Do not restrict the air flow. Air flow must be provided for the unit to operate.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents For Fully Integrated NoFrost Combined Refrigerator-Freezers Instructions de montagePlease Read and Follow These Instructions Installation Guidelines Door swing clearence Figure Planning Information36 914 mm 24-3/4 629 mm 80 2032 mm Cabinet Opening Dimensions FigureMounting the anti tipping device on concrete floors Blocking for SafetyMounting the anti tipping device on wooden floors Figure Water Connection Safety Instructions and WarningsIcemaker IceMakerConnection to the Water Supply Fasten the appliance in the recess InstallationLeveling the Refrigerator Figure Cover plate for 84 cabinetsMounting the attachment brackets onto the door panels Mounting the refrigerator door panels Figures 21 Soft-stop cylinder retracts in the detached state Mounting the ventilation grille

HCS 20 specifications

The Liebherr HCS 20 is a cutting-edge piece of equipment designed for heavy lifting and construction applications. Known for its robust engineering and advanced technologies, this crawler crane has quickly established itself as a preferred choice among professionals in the construction and infrastructure sectors.

One of the main features of the HCS 20 is its impressive lifting capacity. With a maximum load capacity of 200 tons, it can handle a variety of heavy loads with ease, making it suitable for tasks ranging from the assembly of large structures to the transportation of heavy machinery on site. This ability allows operators to conduct more efficient operations, reducing the time needed for lifting tasks and increasing overall productivity.

The HCS 20 is equipped with Liebherr’s innovative Litronic control system. This advanced technology offers precise control over various crane functions, enhancing safety and efficiency. The Litronic system enables real-time monitoring of the crane's performance, ensuring optimal operational parameters are maintained. Operators can easily adjust settings to accommodate the specific requirements of each lifting job.

Another standout characteristic of the HCS 20 is its compact design, which allows for excellent maneuverability in confined spaces. The crane’s crawler undercarriage provides stability and traction on uneven terrain, making it versatile for different job sites. The ability to operate effectively in challenging conditions is a significant advantage for construction and industrial projects.

Safety features are also a priority with the HCS 20. It comes equipped with various safety systems, including load moment limiters and anti-collision technology. These features help prevent overload conditions and ensure safe operation, providing peace of mind for operators and project managers alike.

Moreover, the HCS 20 is designed for quick setup and dismantling. Its modular structure allows for easy transport, making it ideal for projects that require frequent relocation. This efficiency translates to lower costs and reduced downtime, further enhancing its appeal for contractors.

In summary, the Liebherr HCS 20 crawler crane combines exceptional lifting capacity with advanced technologies, making it a top choice for heavy-duty construction tasks. Its precise control systems, safety features, and compact design allow it to excel in various environments, ensuring reliable performance on any job site. As industries continue to evolve, the HCS 20 stands out as a leader in construction technology, promising enhanced productivity and safety for operators.
Top Page Image Contents