Rangemaster U106140-05 To Remove Ignition/light Switch, To Remove Clock, To Remove a Thermostat

Page 30

WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

4.To Remove Ignition/light Switch

Remove the Control Panel - see 1.

NB. The old switch may be destroyed during removal. Remove the old switch from its bezel by griping the switch body behind the control panel and twisting sharply. The switch bezel can then be removed by folding back its locking wings and pushing forward. Fit the new bezel to the control panel by first lining up the raised key on its body with the cutout in the control panel and pushing it in from the front. Assemble the new switch to the bezel by lining up the key sections and pushing home. Fit the new button by pushing in from the front.

Replace Control Panel in reverse order and test for ignition.

5. To Remove Clock

Disconnect from electricity supply.

Remove the Control Panel (See 2). Pull off the timer control button(s).

Remove the timer/mounting bracket assembly from the control panel by removing the fixing screws.

Remove the timer from its mounting bracket by depressing the plastic lugs on the timer case, at the same time pulling the unit forward.

Reassemble in reverse order. When replacing leads refer to the wiring diagram. Check operation of timer.

BEFORE SERVICING ANY GAS CARRYING COMPONENTS TURN OFF GAS SUPPLY.

6. To Remove a Thermostat

Remove RH hotplate tray. (For L H oven remove L H side panel - see 2.) Open appropriate oven door.

Unclip the thermostat phial from the clips at the front of the oven roof. Disconnect tubing nut at rear of thermostat and remove the screw(s) securing the thermostat to the gas rail. Remove thermostat and gasket/seal. When fitting replacement thermostat use the new gasket/seal supplied.

Ensure that the capillary is clipped to the bracket at the front of the oven roof.

Reassemble in reverse order. Check appliance is gas sound. Check operation of thermostat.

7. To Change Grill Control Tap

Remove the facia panel, see 2. Lift up the RH hotplate tray front (see 2). For LP cookers, unplug the FSD lead from the rear of the tap. Undo the gas connection to rear of valve and remove the screw(s) securing tap to gas rail. Remove old tap, discard old gasket/seal. Fit new gasket/seal to new tap.

Reassemble in reverse order. Check tap is adjusted for correct gas. Check appliance is gas sound.

8. To Change Warmer Switch

Remove RH hotplate tray. (see 4). Disconnect wiring from Warmer switch. Remove 2 screws holding switch to mounting panel, taking care not to lose the switch rotation limiter. Fit new switch and reassemble in reverse order. Check for correct operation.

BEFORE SERVICING ANY GAS CARRYING COMPONENTS TURN OFF GAS SUPPLY.

9. To Change Hotplate Control Tap

Remove the facia panel, see 2. Lift up the LH hotplate tray front (see 2). Remove the heat shield (2 screws). Unplug the FSD lead from the rear of the tap. Undo compression fitting at the rear of the tap. Remove the fixings that secure the tap to the gas rail. Remove the tap. Remove and discard the gasket seal. Fit new gasket seal to replacement tap. Re-assemble

in reverse order. Check the appliance is gas sound. Check hotplate ignition.

10. To Change Hotplate Burner Injector

Remove burner cap and head. Remove old jet. Fit new injector. Reassemble in reverse order. Check appliance is gas sound.

11. To Change Hotplate Burner Electrode

Lift off pan supports, remove burner cap. Remove the screw holding the electrode. Pull electrode vertically up sufficiently to grip the lead between thumb and forefinger. Pull off the electrode, but keep hold of the lead. Fit new electrode to the lead. Fix electrode in burner with screw. Replace burner cap. Check the burner ignition. Replace pan supports.

12.To Remove or Change a Hotplate Burner.

Remove the hotplate tray (see 2).

LH hotplate burners

Remove heat shield (2 screws). The burners are mounted in 2’s on cross supports. Disconnect the burner feed pipes at the burners. Remove the screw on the right holding the cross support. Slide the support to the right to release in from the left hand location. Lift the cross support and burners clear. The burners are fixed to the cross supports with 2 screws Remove the appropriate burner and fit the new one. Reassemble in reverse order. Check burner operation is satisfactory.

RH High burner

Disconnect the burner feed pipes at the burner. Fit the new one and reassemble in reverse order. Check burner operation is satisfactory.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Installation & Service Instructions U106140 Gas FSD Users GuideBe safe InstallationThis appliance should not be installed in a boat or caravan Gas and Electricity onContents Hotplate burners Do not use this to turn the burners off. The gasGriddle WarmerGrill Ovens ClockTo set the time of day To stop automatically Auto is showing, you want to reset to manual cookingTo time something that’s cooking minute minder To start and stop the oven automaticallyKey Lock Cooking using the timerClock Special Features To activate the key lockOven cooking ‘S’ Slow cookingOven shelves Handyrack Oven lightStorage Oven cooking guide Griddle Cleaning your cookerHotplate burners Control Panel and DoorsOvens Oven side liningsRemoving the Oven Linings Outside of cooker Cleaning Table HotplatePart Finish Recommended Cleaning Method Oven and GrillMoving your cooker Troubleshooting Power failure Oven temperature getting hotter as the cooker gets olderPower supply You think there may be a problem with it What cleaning materials are recommended for the cooker?0800 111 General Safety InstructionsIf you smell gas Don’t smokeThis appliance is heavy, take care when moving it Location of Cooker InstallationProvision of Ventilation They cannot be converted from one gas to the otherDear Installer You will also need the following toolsElectric drill Positioning the Cooker Unpacking the CookerChecking the parts Moving the Cooker LevellingFitting a stability bracket Gas ConnectionElectrical checks Pressure testingElectrical Connection Hotplate checkFitting the plinth Fitting the oven burner trimOven check Customer careTo Remove Hotplate Trays Servicing NotesTo Remove the Control Panel To Remove Side PanelsTo Remove Clock To Remove Ignition/light SwitchTo Change Warmer Switch To Remove a ThermostatTo Change Grill Burner To Change Oven Burner AssemblyTo Change Grill Injector To Change Grill ElectrodeTo Remove Grill Door To Adjust an Oven Door Catch KeepTo Change Oven Electrode To Change Oven Door Outer PanelTo Change Warmer To Change Oven Door SealTo Change Warmer Neon To Change Ignition GeneratorCircuit Diagram Technical Data

U106140-05 specifications

The Rangemaster U106140-05 is a standout model in the world of kitchen appliances, blending a classic aesthetic with modern functionality. Designed to cater to the needs of both casual cooks and culinary enthusiasts, this model is a prime example of quality craftsmanship and innovative technology.

One of the main features of the Rangemaster U106140-05 is its spacious oven capacity. This appliance is designed to accommodate large meals, making it an ideal choice for families or those who love to entertain. The oven features multiple cooking zones, enabling users to prepare various dishes simultaneously. The generous space ensures that even the largest roasts or multiple trays of cookies can be baked to perfection.

The Rangemaster U106140-05 also incorporates advanced cooking technologies which enhance the overall cooking experience. With features such as fan-assisted cooking, heat is evenly distributed around the oven, ensuring that food is cooked uniformly. Additionally, the true convection option is particularly beneficial for baking, as it helps to achieve consistent results across multiple racks, an essential for dedicated bakers.

Energy efficiency is another hallmark of the Rangemaster U106140-05. The oven is designed with temperature accuracy in mind, allowing users to waste less energy while cooking. Its intelligent system also enables precise heating control, minimizing the risk of overcooking or undercooking food items.

The design of the Rangemaster U106140-05 is equally impressive. It showcases a timeless elegance with a range of finishes and colors that can complement any kitchen decor. The ergonomic knobs and handles not only enhance its visual appeal but also ensure ease of use. The wide glass oven door provides easy visibility, allowing users to monitor cooking progress without heat loss.

Safety features are also a priority in this model. The oven is equipped with cool-touch doors, ensuring that the exterior remains safe to touch even during intense cooking sessions. Furthermore, the residual heat indicators provide an additional layer of safety, informing users when the oven is still hot.

Overall, the Rangemaster U106140-05 stands out as an excellent choice for anyone looking to invest in a reliable, stylish, and efficient cooking appliance. With its combination of spacious design, advanced cooking technologies, energy efficiency, and safety features, it truly meets the demands of modern cooking while maintaining a classic charm.
Top Page Image Contents