Indesit IDL 505 manual Loading the Salt into the Softener, Adjusting Salt Consumption

Page 5
Salt ......

Salt ......

Salt

The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils.

The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.

Loading the Salt into the Softener

Always use salt intended

for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows:

1.Remove the lower rack and then unscrew and remove the cap from the salt container;

2.If you are filling the container for the first time, fill it with water;

3.Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container.

4.Carefully screw the cap back on.

The salt container should be filled after about every 30 wash cycles.

Warning: To prevent rust from forming, we advise you to load the salt before starting a wash cycle.

Adjusting Salt Consumption

The dishwasher is designed to allow for adjusting the amount of salt consumed based

on the harness of the water

used. This is intended to optimize and customize the level of salt consumption so that

it remains at a minimum.

Your Local Water Board can supply the degree of hardness

of the water in your area.

To adjust salt consumption, pro- ceed as follows:

1)Unscrew the cap from the salt container.

2)There is a ring on the container with an arrow on it (see figure to the side), if necessary, rotate the ring in the anti- clockwise direction from the "_" setting towards the "+" sign, based on the hardness of the water being used.

It is recommended that adjustments be made in accord- ance with the following schema:

Water Hardness

 

 

 

 

 

 

 

 

 

 

 

 

 

Salt

Autono-

 

 

 

 

consu-

Clarke

 

 

Selector

my

°fH

mmol/l

mption

degrees

position

(cycles\2-

 

 

(grams/-

 

 

 

 

kg)

 

 

 

 

cycle)

 

 

 

 

 

 

 

 

 

 

 

0 - 14

0 - 17

0 -1,7

/

0

/

 

 

 

 

 

 

14 - 36

18 - 44

1,8 - 4,4

"-"

20

60

 

 

 

 

 

 

36 - 71

45 - 89

4,5 - 8,9

MED

40

40

 

 

 

 

 

 

>71

> 89

> 8,9

"+"

60

25

 

 

 

 

 

 

3

GB

Image 5
Contents Dishwasher Installation and useIDL 500 IDL Page Start/Reset Button Safety Is a Good Habit to Get IntoClose-upView control panel 97/17/EEC LabellingClose-upView Interior Rack Height AdjustorUpper Rack Bottom Sprayer ArmSalt Adjusting Salt ConsumptionSalt Loading the Salt into the SoftenerDetergent Detergent and Rinse AidLoading the detergent Rinse AidHow to Use the Upper Rack How to Use the Lower RackHow to adjust the Upper rack Loading the DishwasherCancelling or modifying a wash cycle in progress… Cycle phase indicator lightsTurning on the Appliance First of all5LQVH Wash Cycle TableNo Solvents or Abrasive Cleaning Products How to Keep Your Dishwasher in ShapeWhen You Go on Holiday Energy Saving TipsTroubleshooting Cleaning and Special MaintenanceThe filter assembly Cleaning the Sprayer ArmsPositioning the Appliance InstallationLevelling the Appliance Cold Water ConnectionHow to connect an alternative plug Replacemente fuse coversElectrical Connection WARNING THIS APPLIANCE MUST BE EARTHEDPage Page Viale Aristide Merloni 47 60044 Fabriano Italy Merloni Elettrodomestici