Installation

Positioning the Appliance

Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the dishwasher, making it level. In any case, the appliance should not be inclined more than 2°.

If the appliance is level, it will help ensure proper perfor- mance.

Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4 cm., or let it run into the sink, making sure to avoid bending or crimping it. Use the speical plastic support that comes with the appliance (see figure to the right). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water.

Adjusting the Back Feet

Insert the appliance into the cutout and then adjust the height using the screws located on the front bottom part of the machine. Use a screwdriver to turn the screws in the clockwise or anti-clockwise direction to increase or decrease the height respectively.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas) connector, inserting the small filter supplied with the

dishwasher and making sure
that it is fastened tightly in
place (see figure 2).
If the water pipes are new or
have not been used for an
extended period of time, let the	A
water run to make sure that
the water is clear and free of
impurities. If this precaution is
not taken, there is a risk that	Fig.2
the water inlet can get blocked
and damage the appliance.

Hot Water Connection

The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60° C.

In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line.

Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is sized for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug, rather than using adpators or the like as they could cause overheating and burns.

Should the electricity supply cable be damaged, we recommend that you only contact authorised Technical Service Centres for the replacement.

CAUTION:

The dishwasher plug must be accessible even when the appliance is installed as a built-in unit so that maintenance can be done safely.

DV 62 specifications

The Indesit DV 62 is a versatile and reliable vented tumble dryer, designed to provide efficient drying without compromising on quality. Equipped with a variety of features and technologies, the DV 62 caters to the needs of busy households looking for performance and convenience.

One of the standout characteristics of the Indesit DV 62 is its 6 kg drying capacity, which makes it suitable for small to medium-sized families. This allows users to effectively dry a substantial amount of laundry in a single load, saving both time and energy. The appliance offers multiple drying programs, including options for cotton, synthetic fabrics, and delicate items. This ensures that all varieties of clothing receive the appropriate treatment, preventing over-drying and damage.

The Indesit DV 62 also features a simple and user-friendly control panel, allowing for easy program selection. With straightforward dial controls, users can quickly set their desired settings without any confusion. The LED display provides clear feedback on the selected program and remaining drying time, keeping users informed throughout the cycle.

Another significant advantage of the DV 62 is its efficient energy management. While this dryer is vented, it is designed to offer optimal energy consumption levels. The appliance incorporates a reverse action drum, which helps to reduce tangling and ensures even drying. This feature is particularly beneficial for larger items such as blankets and bedding, as it allows for a more consistent drying performance.

To maintain the appliance's efficiency, the Indesit DV 62 includes a lint filter that is easy to access and clean, helping to prevent blockages and ensure effective airflow. Regular maintenance and cleaning of the filter contribute to the longevity of the dryer and the quality of its performance.

In terms of safety, the DV 62 is equipped with a range of protective features, including an automatic shut-off function that activates when the door is opened during a drying cycle. This ensures safe operation and adds peace of mind for users.

In summary, the Indesit DV 62 vented tumble dryer combines practicality with user-centric design. With its 6 kg capacity, multiple drying programs, energy-efficient functions, and easy-to-use controls, this appliance is a solid choice for households seeking a dependable solution for their laundry needs. Whether drying everyday clothing or delicate fabrics, the Indesit DV 62 delivers on performance and convenience.