hussman CR3HTO-HTB operation manual Lift-up Glass Maintenance, Periodic Inspection and Maintenance

Page 6

IGFC-CR3H-HTB-1104

dust, grease, oil, and fingerprints without the need for cleaning fluids.Alight spray of the cleaning fluids listed above will reduce the time required for cleaning. These materials have been tested and proven to clean the non glare glass without scratching or damaging theAnti- reflective coating.

Cleaning solvents - for more difficult cleaning jobs, these products are recommended for the cleaning of glass. Care must be taken where they are used. The solvents are tested for use on the outside of the glass. No solvent should be applied directly to food product and food should be protected from overspray unless they carry the USDA-A1 ranking.

The food should be covered or the solution should be sprayed on a cleaning cloth away from the case if it is to be used inside the case with product present.

The following products will not damage the non-glare coating on the glass:

Windex®

Glass-Plus®

Exceed™ Multi Surface Glass Cleaner - from Kay Chemical Company, Greensboro, NC

Warm water

Under no circumstances should the following be used for cleaning glass:

Coarse paper towels

Souring Pads or Powders

Steel wool or steel fiber materials

Blades

Acidic or highlyAlkaline detergents

Fluorine based detergents

Lift-up Glass Maintenance

At Installation and after replacement:

The top cylinders, which allow the raising and lowering of the glass, have been carefully tested for proper tension. However, during shipment, the lubricant inside may have settled. This settling may cause excessive or uneven tension on the glass - to the point of breakage.

Before opening the glass for the first time and after installing new cylinders, it is advisable to perform these three easy steps before completely raising the front glass.

1.Slowly raise and lower each glass section 6 times, to a height of 6".

2.Increase the height to 12", and raise and lower the glass 6 more times.

3.Finally, raise the glass to it's full extension. This should release any settled lubricant in the cylinders, and prevent any stress on the front glass.

After the case is brought to operating temperature the first time, recheck the Allen screws on the glass once the case once the case is in full operation and brought to temperature.

Temperature changes can affect the size and shape of the materials involved, and can cause changes in the secure fit of the glass and the clamp.

CAUTION

Cylinders are a wear item. They are designed:

•To support the glass when fully open •to allow the glass to close slowly

Have your Service Contractor replace the cylinders when required.

Glass is heavy and can cause bodily damage. Check support cylinders for periodic maintenance

Periodic Inspection and Maintenance

Piston cylinders are a wear item. They are designed to support the glass when fully open and to allow the glass to close slowly. Glass is heavy and can cause bodily damage.

Check support cylinders as a part of periodic mainte- nance. Have your Service Contractor replace the cylinders if they show signs of weakness or when

6

Image 6
Contents Hot Top w/ Self Service Heat or Refrig Rev.1104Check your shipment for any possible shortages Receipt of equipmentProvide the customer with the correct parts Case Drawings When wedges are involved in a lineup, set them first Glass Breakage MAY OccurBefore Servicing Lift-up Glass Maintenance Periodic Inspection and MaintenanceAt Installation and after replacement Food Handling and Hot Food Equipment Otherwise indicatedTemperature Adjustment Controls are located at the rear of the caseTimer Operation For Service CallTimer PowerBottomelectricbox FCL-13A-R/M Switch BLSTB432PUNVHP-A BUSHINGHEYCO#20531/2PCB Assembly Timer BALLAST125-01-3273 MagneteBallast Magnete B432PUNVHP Power Neutral Ground Bottomelectricbox SHINKOFCL-13A-R/M SwitchWiring MarsShinko Ballast Magnete B432PUNVHP Power Neutral Ground TimerPcbassembly RelaymarsAppendix A. Temperature Guidelines Appendix B. Application RecommendationsAppendix D. Recommendations to user Production Order # ****** Drawing Title PcbassemblytimerProject Title Revisions DescriptionIGFC-CR3H-HTB-1104 Limited Warranty Service Record

CR3HTO-HTB specifications

The Hussman CR3HTO-HTB is a state-of-the-art refrigeration display case designed primarily for convenience stores, supermarkets, and other retail establishments that require an efficient and attractive solution for showcasing perishable products. The model exemplifies Hussman's commitment to innovation, sustainability, and energy efficiency while maintaining optimal product visibility.

One of the standout features of the CR3HTO-HTB is its sleek design, which incorporates a low-profile structure and expansive glass panels. This design not only enhances the aesthetic appeal of any retail space but also maximizes product visibility, allowing customers to easily browse through displayed items. The curved glass front provides an unobstructed view, making it easier for shoppers to see products from various angles.

In terms of technology, the CR3HTO-HTB boasts advanced climate control systems that ensure consistent temperature regulation. The unit utilizes a high-efficiency refrigeration system that can maintain optimal storage temperatures for a wide range of perishable goods, including dairy products, beverages, and prepared meals. Additionally, it features a digital thermostat for precise temperature management and monitoring, providing retailers with peace of mind that their products are stored safely.

Energy efficiency is a significant consideration with the CR3HTO-HTB. Equipped with LED lighting, the unit illuminates the display case without generating excessive heat, which helps maintain a stable internal environment and reduces energy consumption. Moreover, the refrigeration unit is designed with eco-friendly refrigerants, minimizing its impact on the environment. The incorporation of energy-efficient components not only complies with global sustainability standards but also helps operators reduce operational costs.

Another key characteristic of the Hussman CR3HTO-HTB is its adaptability. The case can be configured in multiple ways to fit different layouts and store formats, catering to diverse retail needs. Its modular design allows for easy integration with other display units, making it an ideal choice for retailers looking to create an optimized shopping experience.

In summary, the Hussman CR3HTO-HTB is a modern refrigeration display case that combines aesthetic design, superior technology, and energy efficiency. Its features, such as advanced climate control, exceptional visibility, and flexibility, make it a top choice for retailers aiming to enhance product presentation while committing to sustainability.