Heatcraft Refrigeration Products H-IM-79E manual

Checking Operation of Expansion Valve

Checking Operation Of Expansion Valve (EEV)

To check if the expansion valve is closing properly:

Install a pressure gauge-set to suction line at the condensing unit. With the system running, close the valve on the liquid line, at the con densing unit. The system should pumpdown and shut off on the Low Pressure switch (LPS). If the system does not pumpdown and trip on the LPS then the compressor valves are weak and needs to be changed.

After the system pumps-down and trip on the LPS, put the system in the service mode. This will cause the Expansion valve to close. Open the valve on the liquid line, at the condensing unit. The suction pressure reading on the gauge set should not increase. If the suction pressure increases then the expansion valve is leaking and should be changed.

The Expansion valve position can be monitored from the LED display pressing the “MONITOR” button and scrolling to ESP. This will indicate the number of steps the valve is open.

This can also be checked by using the EXV test pins on the board. This is indicated by a 0 to 5 Volts DC signal. At 0 Volt the valve is closed and at 5 Volts the valve is fully open. At values between 0 and 5 Volt, the valve will be opened proportionately.

Use the “MONITOR” button to display “SCP”” Evaporator Suction Pressure. Record the pressure displayed. Start the system and observe the pressure displayed. If the pressure does not increase, the expansion valve could be defective.

If the system is running, use the “MONITOR” button to display “SCP” Evaporator Suction Pressure. Record the pressure displayed. While the system is running, press the “FORCE SERVICE” button. Observe the pressure while the system is pumping down. The pressure should decrease. If it does not, this indicates a defective valve.

Expansion Valve Motor Winding Resistance

If the expansion valve is suspected of not functioning properly the motor windings resistance should be measured. This is a bipolar motor with two windings. Measure the resistance at the pins, on top of the valve, between locations A and B

or C and D.

(Note that the pins are not labeled A, B, C, D. This labeling is just for reference. Also, two of the pins, at location B and location D, have a wider spacing between them than between location A and C)

Expansion Valve

A• •C

••

B D

Motor Winding

Pins

For valve size 29320003 and 2930004, the resistance measured between pin locations A and B or C and D should be approximately 336 Ohms when valve is at 75ºF.

For valve size 2930007, 29320008, 29320013 and 29320014, the resistance measured between pin locations A and B or C and D should be approximately 116 Ohms when the valve is at 75ºF.

Continues to Page 21

H-IM-79E specifications

Heatcraft Refrigeration Products has long been a leader in eco-friendly and efficient cooling solutions, and the H-IM-79E is a prime example of their commitment to innovation and sustainability. Designed for commercial use, the H-IM-79E is a high-performance refrigeration unit ideal for supermarkets, convenience stores, and restaurants, where reliable temperature control is essential.

One of the standout features of the H-IM-79E is its energy efficiency. This unit employs advanced compressor technology that optimizes power consumption without sacrificing cooling performance. In addition, it is designed to minimize operational costs, making it an attractive option for businesses looking to reduce their energy bills while maintaining high standards of refrigeration.

The H-IM-79E integrates a robust refrigerant management system that uses environmentally friendly refrigerants, aligning with Heatcraft's commitment to reducing the carbon footprint of their products. This not only helps businesses comply with environmental regulations but also promotes a healthier planet for future generations.

Another key characteristic of the H-IM-79E is its superior temperature stability. The unit is equipped with precision temperature control technology that ensures consistent cooling performance, preventing temperature fluctuations that can compromise food quality and safety. This reliability is crucial in commercial settings where maintaining optimal storage conditions is essential.

The design of the H-IM-79E is also noteworthy. It features a compact footprint, allowing it to fit seamlessly into various commercial environments without taking up valuable floor space. Additionally, the unit is built with durable materials, ensuring longevity and minimizing maintenance needs.

User-friendly interfaces make the H-IM-79E easy to operate. It includes advanced monitoring and diagnostics capabilities, allowing business owners to track performance in real-time and address potential issues before they escalate. The incorporation of smart technologies means that operators can remotely monitor and control the system, providing flexibility and peace of mind.

In summary, the Heatcraft Refrigeration Products H-IM-79E stands out for its energy efficiency, eco-friendly refrigerant use, reliable temperature control, compact design, and user-friendly features. This combination of attributes makes it an ideal choice for businesses that prioritize both sustainability and performance in their refrigeration needs.