hussman FMSS-L operation manual Installation Contd, Joint Trim

Page 4

IGSS-FMSS-L-0508

Installation (Cont'd)

NOTE: A. To avoid removing concrete flooring, begin lineup leveling from the highest point of the store floor.

B. When wedges are involved in a lineup, set them first.

All cases were leveled and joined prior to shipment to insure the closest possible fit when cases are joined in the field. When joining, use a carpenters level and shim legs accordingly. Case must be raised correctly, under legs where support is best, to prevent damage to case.

1.Check level of floor where cases are to be set. Determine the highest point of the floor; cases will be set off this point.

2.Level and set the first case, carefully guiding the electrical, refrigeration and drain lines through the parent case. Case must be raised under legs where support is best to prevent damage to case. Internal bracing may be removed at this time.

3.Set second case as close as possible to the first case carefully guiding its electrical, refrigeration and drain lines through the parent case, and level case to the first using the instructions in step one.

4.Apply masking tape 1/8” in from end of case on inside and outside rear mullion on both cases to be joined.

5.Apply liberal bead of case joint sealant (butyl) to

(dotted area shown in figure) first case. Apply heavy amount to cover entire shaded area.

DO NOT USE PERMAGUM!

Fig. 2, #1

It is the contractor’s responsibility to install case(s) according to local construction and health codes.

6.Slide second case up to first case snugly. Then level second case to the first case so glass front, bumper and top are flush.

Do not use the top bracket on the

rear mullion to pull the cases together.

7.To compress silicone at joint, use two Jurgenson wood clamps. Make sure case is level from front to back and side to side on inside bulkheads at joint.

8.Attach sections together with the two 3/8” bolts provided, below the deck at the mullion towards the rear of the FMSS-L. Remove clamps.

9.Apply bead of silicone to top of bulkheads and slip on stainless steel bulkhead cap. Also apply silicone to seam between overhead light tubes.

10.VERY IMPORTANT! Apply liberal amounts of black silicone to fill all voids down to bulkhead.

Proper case-joint sealing is

extremely important to prevent

water leaks!

11.Use finger to smooth silicone as thin as possible at masking tape on inside and outside of rear mullion (apply additional silicone if necessary). Remove tape applied on line #3.

Joint Trim

After cases have been leveled and joined, and refrigeration, electrical, and wasted piping work completed, install the splashguards. Fasten along the top edge, or center, with #10 X 3/3” sheet metal screws.

DO NOT SEAL JOINT TRIM TO FLOOR!

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Case-front Self Service RevTable of Contents General InstructionsInstallation Cut and Plan ViewsInstallation Contd Joint TrimPlumbing RefrigerationRefrigeration Contd Electrical User InformationWhen cleaning User Information ContdMaintenance Electrical Wiring DiagramsWiring Diagrams Loading208 V 240 L1 5.7 L2 4.8 Case Electric Defrost115 208 240 Power ~208/240 VAC 1Ø 50/60Hz. 4WCase Electric DEFROST-DUAL Temp Power ~208/240 VAC 1Ø 50/60Hz 115 V 208 24010.0 Case Electric DEFROST-DUAL Temp page 1115 Contd11.3 13.3 Wiring 115 V 208 240 14.1L3 ~ Raychem 10BUT-CR-10W208 V 240 L1 11.4 L2 9.6 Wiring Diagrams ContdDual Temp FMSS-L Case DWG # W1400005 Appendix A. Temperature Guidelines AppendicesAppendix B. Application Recommendations Open DisplayAppendices Contd Appendix D. Recommendations to UserAppendices Contd Service Record
Related manuals
Manual 25 pages 52.65 Kb

FMSS-L specifications

The Hussman FMSS-L is a state-of-the-art commercial refrigeration display case, specifically designed to meet the needs of grocery stores, convenience retailers, and foodservice establishments. Known for its advanced features and innovative technologies, the FMSS-L provides an ideal solution for merchandising fresh food products while ensuring optimal temperature control and energy efficiency.

One of the main features of the FMSS-L is its impressive visibility. Engineered with a low front profile and curved glass design, this model maximizes product exposure, enticing customers and enhancing the shopping experience. The spacious interior layout allows for ample product display, taking full advantage of the vertical space available in retail environments.

The FMSS-L incorporates advanced refrigeration technology, ensuring that food items are kept at safe temperatures while minimizing energy consumption. Its well-insulated case construction is designed for enhanced energy efficiency and durability. This is complemented by smart refrigeration controls and variable-speed fans, which adjust airflow based on cooling requirements, further optimizing energy use.

Hussman's commitment to energy efficiency is evident in the use of eco-friendly refrigerants. The FMSS-L is designed to comply with the latest environmental regulations, ensuring that businesses can operate sustainably without sacrificing performance. Additionally, energy-efficient LED lighting enhances product visibility while using significantly less energy than traditional lighting options.

Other notable characteristics of the FMSS-L include adjustable shelving, which allows retailers to customize the display according to their specific needs. The shelves can be easily repositioned to accommodate various product sizes and shapes, promoting flexibility in merchandising. Furthermore, the case is equipped with a self-closing glass door system that provides easy access while also reducing energy loss.

Maintenance is straightforward with the FMSS-L, thanks to its accessible components and user-friendly design. Hussman prioritizes serviceability, allowing for prompt repairs and reduced downtime, which are critical for busy retail environments.

Overall, the Hussman FMSS-L is a well-engineered refrigeration solution that combines aesthetic appeal, advanced technology, and energy efficiency, making it an excellent choice for retailers looking to showcase fresh food products effectively while maintaining operational sustainability. With its blend of innovative features and practicality, the FMSS-L stands out as a reliable partner in the competitive retail food landscape.
Top Page Image Contents