Temperature Control and Selection, Defrost

Temperature

Control and Selection

The temperature control knob is located in the grille below the door. There is a pointer on the grille at the

12:00 position to indi-
cate knob position.
The "OFF" position will
turn the refrigeration
system off. Positions 1
is the warmest setting
and setting 7 is the
coldest. Wait at least 2
hours between tem-	COLDER
perature adjustments
to find a temperature
that suits you.

The refrigerator section temperature of the unit can be adjusted using the adjusting slide located in the left side and rear of the refrigeration section. Turn in the cold direction indicted to make the refrigeration section cold- er and the opposite to warm the refrigeration section.

Icemaker Operation

•Make certain water pressure is at least 20 psi and no more than 120 psi and is turned on.

•The unit must be installed level for proper icemak- er operation.

•The shut off arm wire must be down in its lowest position for the icemaker to operate.

•Make certain there are no obstructions in the fan inlet and outlet. The fan is located beside the ice- maker at the top of the freezer section.

•When the freezer section and icemaker unit has sufficiently cooled, the icemaker will harvest ice cubes automatically.

•When the ice bucket is full, the icemaker will auto- matically shut off.

•You may manually stop the icemaker by raising the shut-off arm to the locking position at the up most position.

Defrost

This units uses an electronic control system to control both defrost and refrigeration functions. This feature eliminates the inconvenience of manual defrosting of the evaporator in normal conditions. If commodities or ice accidentally clog the drip tray, the obstruction must be removed for proper defrost performance. It is normal for some water droplets to be left on the evaporator or drip tray. These will refreeze and be removed in the next defrost cycle.

Defrosting is factory set to run after the compressor has run approximately 12 hours. For climates with high humidity levels and/or repeated opening of the door, an optional 6-hour compressor run time is already pro- grammed into the control. A switch will have to be set at the control for this change to take place (consult your distributor or authorized service center).

A drip tray heater is located in the unit for proper removal of condensation. The heater will remain on as long as the unit is plugged in. The control knob will not turn the heater off. Unplug or disconnect power to the unit if you are planning to leave the unit off or unattend- ed for extended periods of time.

Arm down, Icemaker will operate

Arm up, stops operation

Important

When operation of the appliance is to be discontinued for any length of time, the ice cube cavity in the icemak- er should be emptied and dried. The water supply and power supply should also be shut off and the ice bucket should be emptied and cleaned.

If the ice is not used regularly, it will clump together with time. For best ice results, discard ice in the bin as required and allow the icemaker to make a new fresh batch of ice.

6CiM specifications

Marvel Industries' 6CiM is a cutting-edge modular system designed to revolutionize the way industries approach manufacturing and production. Emanating from the heart of innovative engineering, the 6CiM stands for "Sixth Generation Cross-Industry Module," embodying the perfect blend of flexibility, efficiency, and advanced technology.

One of the standout features of the 6CiM is its modularity. This system can be easily customized and scaled according to the specific needs of various industries, including automotive, aerospace, electronics, and consumer goods. The modular components are designed for rapid assembly and disassembly, allowing businesses to pivot quickly in response to market demands or shifts in production strategy.

Technology is at the forefront of the 6CiM’s design. Equipped with state-of-the-art automation capabilities, the system leverages artificial intelligence and machine learning algorithms to optimize production processes. These technologies allow for real-time data collection and analysis, enabling predictive maintenance and reducing downtime. This intelligent approach ensures that production lines remain operational and efficient, ultimately leading to significant cost savings.

Another significant characteristic of the 6CiM is its integration of sustainable practices. Marvel Industries has prioritized eco-friendliness in its design, utilizing recyclable materials and energy-efficient components. The system’s architecture is optimized for reduced energy consumption, aligning with global initiatives to promote greener manufacturing practices.

Additionally, the 6CiM supports seamless connectivity with IoT devices, facilitating remote monitoring and control. This capability allows operators to manage production lines from anywhere in the world, enhancing productivity and flexibility.

Safety features are also paramount in the design of the 6CiM. The system includes various safeguards and automated error-checking protocols to ensure worker safety and minimize the likelihood of accidents on the shop floor.

In summary, Marvel Industries' 6CiM represents a transformative shift in modular manufacturing systems. With its customizable design, advanced automation, sustainability focus, and commitment to safety, the 6CiM is setting new standards in the manufacturing landscape, paving the way for more adaptable and efficient production environments.