PRE-INSTALLATION Instructions Area Preparation

PRE-INSTALLATION INSTRUCTIONS

AREA

PREPARATION

Step 2

When units are installed side by side, a separating filler strip is recommended. The filler strip width should be added to the finished rough opening dimension. A filler strip must also be used when units are installed hinge to hinge.

IMPORTANT: For proper operation and use the door must open a minimum of 90 0 • A minimum 2" filler must be used in corner installations to assure a 90 0 door opening. Remember to allow enough clearance in front of unit for full door swing, Minimum door clearance listed in Figure 2.

IMPORTANT NOTE: We also require the floor under

the refrigerator to be at the same level as the surrounding finished floor.

IACAUTION I

Any finished flooring should be protected with appropriate material to avoid damage from very

heavy appliance.

If unit fits under soffit with clearance between top of unit and soffit of 1" or less as in Figure 3 unit does not require blocking, otherwise blocking is required. Refer to step 8.

ELECTRICAL INSTRUCTIONS

Step 3

Rough in the electrical outlet following the "Pre-Installation Specifications". See Figure 1.

A 115 volt, 60 Hz, 15 amp fused electrical supply is required. It is recommended that a separate circuit, serving only this appliance, be provided.

Follow any other local codes or ordinances that may also apply.

IAWARNINQ]

Do not use an extension cord, or two prong adapter. Electrical ground is required on this appliance.

Do not under any circumstances remove the power supply cord ground prong.

This appliance is factory equipped with a power supply cord with a 3-prong grounding plug. It must be plugged into a mating 3-prong grounding type wall receptacle grounded in accordance with the National Electrical Code and local codes and ordinances. See Figure 4.

PLUMBING INSTRUCTIONS

Step 4

For units with automatic icemaker, rough in the water supply line.

Connect a '/4" copper line to the house supply being sure to use an easily accessible shut off valve between the supply and your refrigerator (approximately 6" from the compression fitting). The icemaker operates on water pressure of 20 to 100 PSI.

NOTE: A line filter is required when water conditions have a high sediment content. Do not use "self piercing" valves. Saddle valve kit (part #4-20-088-0) available from your distributor.

COMPRESSION

FITTING

Figure 5

Route the water line thru the wall no more than 3" from floor when routed under unit. See Figure 6.

NOTE: Regardless of the routing, allow for at least 3 feet of excess copper tub- ing to remain outside wall or floor for easy connection to the unit.

		COMPRESSION
SLAB FLOOR		FITTING

Figure 6

UNPACKING

Step 5

Uncrate unit, remove wood base and discard the shipping bolts which secure the wood base to the bottom of the unit. Do not discard wood block

Figure 4

Route the water line up thru the floor within '/2" from wall, no higher than 3" from floor when routed under unit. See Figure 5.

and hardware to be used for blocking your unit.

In addition retract front leveler legs to ensure easier movement of the unit for installation.

550, 542, 561, 532, 511 specifications

Sub-Zero, a renowned name in luxury refrigeration, has long set the standard for high-performance refrigeration with its exceptional line of products, including models 590, 511, 532, 561, and 542. Each of these models showcases advanced features and cutting-edge technology designed to preserve food freshness while enhancing kitchen aesthetics.

The Sub-Zero 590 is a standout model known for its dual refrigeration system, which employs separate systems for the refrigerator and freezer compartments. This innovative approach allows for optimal humidity control and temperature management, preventing cross-contamination of odors and ensuring that perishables remain fresh for longer. Additionally, the 590 boasts a sleek design that can be seamlessly integrated into any kitchen decor.

Model 511 is designed with convenience in mind. Its compact design makes it an excellent choice for smaller kitchens or bar areas. This model continues the tradition of Sub-Zero's high standards, featuring advanced cooling technologies and smart storage solutions, such as adjustable shelving and door storage, maximizing usable space without compromising on performance.

The Sub-Zero 532 elevates the refrigeration experience with its advanced air purification system, which filters out particles and ethylene gas, a natural compound that accelerates ripening in fruits and vegetables. This ensures that your food stays fresher, longer, while preserving its nutritional quality. The model also includes features such as tempered glass shelves and LED lighting, providing both functionality and elegance.

The 561 model impresses with its built-in design, allowing for perfect integration into cabinetry for a custom look. This model offers a generous capacity while maintaining a sleek exterior. Furthermore, it includes advanced technology like a microprocessor control panel that monitors and adjusts temperatures, ensuring that your food is stored under ideal conditions.

Lastly, the Sub-Zero 542 showcases a classic built-in refrigerator/freezer configuration. Its signature design includes the option for a panel-ready finish, allowing homeowners to match it to their cabinetry. With features like smart touch controls and an advanced cooling system that maintains consistent temperatures, the 542 guarantees reliability and performance.

These Sub-Zero models represent the pinnacle of refrigeration technology, with features that prioritize freshness, convenience, and luxury aesthetics, making them a perfect addition to any modern kitchen.