Construction, Hardware and Insulation
Cabinet exterior front, one piece sides, louver assembly and doors are constructed of 20 gauge stainless steel with #4 finish. Cabinet interior and door liners are constructed of stainless steel (anodized aluminum in the A-Series). The exterior cabinet top, and bottom are constructed of heavy gauge aluminized steel. The exterior cabinet back on reach-in models is constructed of heavy gauge aluminized steel. A set of four (4) adjustable 6" high stainless steel legs are included.
Doors are equipped with a gasket protecting metal door pan, removable plug cylinder locks and guaranteed for life cam-lift, gravity action, self-closing metal, glide hinges with stay open feature at 120 degrees. Hinges include a concealed switch to automatically activate the interior incandescent lighting. Guaranteed for life, work flow door handles are mounted horizontally over recess in door which limits protrusion from door face into aisleways. Doors have seamless, polished metal corners.
Easily removable for cleaning, vinyl magnetic door gasket assures tight door seal. Anti condensate heaters are located behind each door opening.
Both the cabinet and doors are insulated with an average of 2" thick high density, non-CFC, foamed in place polyurethane.
DIMENSIONAL DATA | R/ADH132WUT | R/ADH132WPUT |
Cabinet Type | Reach-In | Pass-Thru |
Net capacity total cu. ft. | 20.6 (584 cu l) | 20.6 (584 cu l) |
Length - overall in. | 297⁄8 (75.9 cm) | 297⁄8 (75.9 cm) |
Depth - overall in. | 35 (88.8 cm) | 3715⁄16 (96.4 cm) |
Depth - over body in. | 32 (81.3 cm) | 32 (81.3 cm) |
| | |
Depth - door(s) open 90° in. | 5711⁄16 (146.5 cm) | 833⁄8 (211.8 cm) |
Clear door width in. | 211⁄8 (53.6 cm) | 211⁄8 (53.6 cm) |
Clear half-door height in. | 271⁄2 (69.9 cm) | 271⁄2 (69.9 cm) |
Height - overall on 6" legs | 831⁄4 (211.5 cm) | 831⁄4 (211.5 cm) |
No. Standard Shelves | 2 | 2 |
Shelf area total sq. ft.1 | 28.0 (2.6 sq m) | 28.0 (2.6 sq m) |
Shelf area refrigerator. sq. ft.1 | 14.0 (1.3 sq m) | 14.0 (1.3 sq m) |
| | |
Shelf area heated section sq. ft.1 | 14.0 (1.3 sq m) | 14.0 (1.3 sq m) |
| | |
RDH Net Wt. lbs. | 380 (172 kg) | 405 (184 kg) |
| | |
ADH Net Wt. lbs. | 330 (150 kg) | 355 (161 kg) |
ELECTRICAL DATA | | |
Voltage | 208/115/60/1 | 208/115/60/1 |
Feed wires with Ground | 4 | 4 |
Wattage @ 208V | 1500 | 1500 |
| | |
Full load amperes | 11.0 | 11.0 |
| | |
REFRIGERATION DATA | | |
| | |
Refrigerant | R-134a | R-134a |
BTU/HR H.P.2 | 2220 (1⁄3 HP) | 2220 (1⁄3 HP) |
NOTES NOTE: Figures in parentheses reflect metric equivalents.
1= Area of standard shelf compliment only, does not include storage area of additional shelves or available on cabinet bottom.
2= Based on a 90 degree F ambient and 20 degree F evaporator.
3= For approximate remote weights deduct 40 lbs. from respective net or gross weight. For other information on remote models, please refer to spec sheet 12-2.
Refrigeration System
Atop mounted, self-contained, balanced refrigeration system using R-134a refrigerant is conveniently located behind the one piece louver assembly. These models feature an easy to clean front facing condenser, thermostatic expansion valve, air-cooled hermetic compressor, plenum effect blower coil, large, high humidity evaporator coil, and a bottom mounted electric condensate evaporator.
Biased return air duct protects against introduction of warm kitchen air, promoting even temperature maintenance and efficient operation.
A 9' cord and plug is provided standard. Standard operating temperatures are 34 to 38°F for the refrigerator compartment and 135 to 180°F for the heated compartment.
Heating System
A low watt density, serpentine style, heater is employed for the generation of electric heat. Low velocity air is forced across its large surface area to efficiently move heat radiating away from these through a down-air distribution duct, where it is then evenly distributed throughout the cabinet, assuring the proper holding environment for hot food product, without drying. A vent, located at the top of the cabinet, is included for positive humidity control.
Controller
The easy to use water resistant INTELA-TRAUL®microprocessor control system is supplied standard. Unit is NAFEM Data Protocol communication (NDP) ready. Optional hardware required to be NDP compliant. Third party software required for network connection. It includes a 3-Digit LED Display, Fahrenheit or Celsius Temperature Scale Display Capability, and an RS485 data port. In addition it includes audio/visual alarms for: Hi/Lo Cabinet Temperature, Door Open, Clean Condenser, Evaporator Coil and Discharge Line Sensor Failures, and Power Supply Interruption. A separate control is provided for both the refrigerated and heated compartments.
Interior
Standard interior arrangements include three (3) chrome plated wire shelves per section, mounted on pilasters. Shelves are full-width, and do not have any large gaps between them requiring the use of "bridge" or "junior shelves." Recommended load limit per shelf should not exceed 225 lbs. Optional tray slides may be purchased in combination with, or in lieu of these. Both standard and optional interior arrangements are completely installed at the factory.
Warranties
Both a one year parts and labor warranty and a five year compressor warranty (self- contained models only) are provided standard. An optional 2nd year extended parts and labor warranty is also available. In addition the INTELA-TRAUL®controls are warranted by a two year parts and labor warranty.
Equipped With One NEMA L14-20P Plug
NOTE: Full load amps and plug style may vary depending on electrical options chosen and condensing unit employed.
REQUIRED CLEARANCES
In order to assure optimum performance, the condensing unit MUST have an adequate supply of air for cooling purposes. Therefore, the operating location must either have a minimum of 12” clearance overhead of the condensing unit or allow for unrestricted air flow at the back of the unit. Clearance of at least 12” above is required in order to perform certain maintenance tasks.
