Gladiator Garageworks Freezer manual Door Closing, Door Alignment, Tools Needed, Parts Supplied

Page 7

¸¸iii¸¸iiii:i!!ii :iii ::::::¸ iiiiiiii :::iiiiiiii ::; i

NOTE: If you have the casters installed on your freezer, the leveling screws will not work. Shims can be placed under the casters to level a freezer that has casters installed.

Door Closing

Your freezer has two front adjustable rollers - one on the right and one on the left. If your freezer seems unsteady or you want the

doors to close easier, adjust the freezer's tilt using the instructions below:

1.Plug into a grounded 3 prong outlet.

2.Move the freezer into its final position.

3.Remove the base grille (see Base Grille graphic). The two leveling screws are part of the front roner assemblies which are at the base of the freezer on either side.

4.Use a screwdriver to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the freezer or turn the leveling screw to the left to lower that side. It may

take several turns of the leveling screws to adjust the tilt of the freezer.

NOTE: Having someone push against the top of the freezer takes some weight oft the leveling screws and rollers. This makes it easier to adjust the screws.

5.Open both doors again and check to make sure that they close as easily as you like. If not, tilt the freezer slightly more to the rear by turning both leveling screws to the right, It may

take several more turns, and you should turn both leveling screws the same amount.

6.Replace the base grille.

Door Alignment

If the space between your doors looks uneven, you can adjust it using the instructions below:

1.Pry off the top hinge cover.

2.Loosen the top hinge screws using a %6 in. socket or wrench.

3.Have someone hold the door in place or put a spacer between the doors while you tighten the top hinge screws.

4.Replace the top hinge cover.

5.Place the freezer on its side on top of the cardboard or protective material. Make sure the door hinge is facing upward.

IMPORTANT: It is important that the door hinge face

Check that you have everything necessary for correct assembly. Proper assembly is your responsibility.

Tools Needed:

V2in. Socket wrench or nut • 3/8in. Socket wrench or nut

 

driver

 

 

driver

 

V2 in. Wrench

 

 

 

 

Parts Supplied:

 

 

 

 

Rigid Casters

(2)

V4-20X 1 V4in. Hex-head

Swivel Casters

(2)

 

bolts (4)

 

 

 

 

5/16-18 Self-locking

V4-20x 1 V4in. lock

washers (4)

 

 

hex-nuts (16)

 

 

 

 

 

 

 

 

%6-18 x 7/8in. Hex-head

bolts •

Caster brackets (located in

FeaturePak)

(2)

 

(I 6)

 

 

 

 

 

 

 

 

 

 

 

Plastic skids

(shipped with

 

 

 

 

the freezer)

 

1.Before you begin, turn the lower compartment control to off, unplug freezer or disconnect power.

2.Remove food and any adjustable shelves and bins from freezer.

3.Open the lower compartment door and remove the base grille. Remove the grille by grasping the grille with both hands, lifting up and pulling bottom of the grille toward you.

4.Place the plastic skids (shipped with the freezer) on the floor at least 3 ft. (91.44 cm) apart. Lay a piece of cardboard or other protective material over the skids. This will elevate the

freezer to allow for easier caster installation and also protect it from scratches.

NOTE: If the skids have been discarded or are not available, 2 in. x 4 in. boards may be used.

Image 7
Contents FREEZEP.ATORTMFREEZER Freezeratortmcongelador Ensuring Proper Air Circulation Full-Width Wire BasketFreezer Doors Removing, Reversing optional and Replacing..5 Door Closing AlignmentBefore you throw away your old refrigerator or fezer FreezersafewFailure to do so can result in death or brain damage Failure to do so can result in death, explosion Cleaning before useRemoving packaging materials Cabinet Bottom Hinge Top HingeRemoval of Door Stops Parts Supplied Door ClosingDoor Alignment Tools NeededLower Rear Corner Lower Front CornerFreezeruse Complete the AssemblyUpper Compartment Control To change the upper compartment to Freeze mode Uppercompartment FeaturesTo remove and replace a half-width basket Lowercompartment FeaturesTo remove and replace full width wire basket To remove and replace a shelfDoor Feaiures Failure to do so can result in death, explosion, or fire Cleaning your freezer Unplug freezer or disconnect powerFreezercare Explosion HazardTemperature is too warm TroubleshootingOur consultants provide assistance with Assistanceor ServiceIf you need replacement parts Installation informationGladiator TM GarageWorks will not pay for Gladiatorgarageworks Freezeratorfreezerwarranty

Freezer specifications

The Gladiator Garageworks Freezer is an innovative storage solution designed specifically for those who require extra freezing capacity to keep food fresh and organized. Built with durability and functionality in mind, this freezer is an essential addition to any garage, workshop, or utility space.

One of the standout features of the Gladiator Garageworks Freezer is its robust construction. The heavy-duty steel exterior not only ensures longevity but also offers a sleek finish that complements any garage aesthetic. The freezer is built to withstand the rigors of a garage environment, making it resistant to dents and scratches. This durability ensures that the freezer maintains its appearance and performance over time.

Equipped with a significant freezing capacity, the Gladiator Freezer can handle large quantities of meat, vegetables, and other perishable goods without compromising on space. With adjustable shelving and bins, users can easily organize and access their frozen items. The flexible storage solution allows for customization based on the user’s specific needs, making it convenient for any household.

Another remarkable characteristic of the Gladiator Garageworks Freezer is its energy-efficient design. Featuring advanced insulation technology, this freezer maintains optimal temperatures while consuming minimal energy. This not only reduces energy costs but also aligns with the growing demand for eco-friendly appliances in the modern home.

The freezer is designed with user-friendly controls that make it simple to set ideal temperatures and monitor performance. With an easy-to-read digital display, users can quickly check on the status of their stored items. Moreover, it includes a power-on light and an adjustable thermostat, providing hassle-free management of food storage conditions.

In addition, the Gladiator Freezer includes a self-defrost function, minimizing ice buildup and ensuring consistent performance. This feature saves users time and effort, allowing them to focus on other tasks without worrying about maintenance.

The Gladiator Garageworks Freezer is versatile and can be integrated into a variety of settings, from family homes to outdoor adventures. Its compact design allows it to fit seamlessly with other Gladiator storage solutions, creating a cohesive and organized garage space.

In conclusion, the Gladiator Garageworks Freezer combines durability, efficiency, and user convenience in one remarkable appliance. With its robust features and innovative technologies, it stands out as a reliable solution for anyone looking to maximize their freezing storage capabilities.