Whirlpool W10533016A Make Gas Connection, Typical rigid pipe connection, Floor Mounting

Page 8

3.Determine and mark centerline of the cutout space. The mounting can be installed on either the left side or right side of the cutout. Position mounting bracket against the wall in the cutout so that the V-notch of the bracket is 12⁵³⁄₆₄"

(32.6 cm) from centerline as shown.

B

Centerline

A

A. 12⁵³⁄₆₄" (32.6 cm)

B. Bracket V-notch

4.Drill two ¹⁄₈" (3 mm) holes that correspond to the bracket holes of the determined mounting method. See the following illustrations.

Floor Mounting

Rear position

Front position

Diagonal (2 options)

Wall Mounting

5.Using the Phillips screwdriver, mount anti-tip bracket to the wall or floor with the two #12 x 1⁵⁄₈" screws provided.

6.Move range close enough to opening to allow for final gas and electrical connections. Remove shipping base, cardboard or hardboard from under range.

7.Move range into its final location, making sure rear leveling leg slides into anti-tip bracket.

8.Move range forward onto shipping base, cardboard or hardboard to continue installing the range using the following installation instructions.

Make Gas Connection

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Typical rigid pipe connection

A combination of pipe fittings must be used to connect the range to the existing gas line. Your connections may be different, according to the supply line type, size and location.

1.Apply pipe-joint compound made for use with LP gas to all pipe thread connections.

2.Using a pipe wrench to tighten, connect the gas supply to the range.

 

B

 

C

 

A

 

D

 

E

 

F

 

G

A. Pressure regulator

D. Union

connection fitting

E. Nipple

B. 90° elbow

F. Manual shutoff valve

C. Black iron pipe

G. ½" or ¾" gas pipe

Typical flexible connection

1.Apply pipe-joint compound made for use with LP gas to the smaller thread ends of the flexible connector adapters (see B and F in the following illustration).

2.Attach one adapter to the gas pressure regulator and the other adapter to the gas shutoff valve. Tighten both adapters.

8

Image 8
Contents Installation Instructions 30 76.2 CM Freestanding GAS Ranges Range Safety Your safety and the safety of others are very importantAnti-Tip Bracket Range Foot Location Requirements Installation RequirementsTools and Parts Mobile Home Additional Installation Requirements Product Dimensions Cabinet DimensionsMobile home installations require Electrical RequirementsGas Supply Requirements Type of GasGas Supply Line Gas Pressure RegulatorInstallation Instructions Install Anti-Tip BracketGas Supply Pressure Testing Unpack RangeMake Gas Connection Typical rigid pipe connectionTypical flexible connection Floor MountingVerify Anti-Tip Bracket Is Installed Engaged Complete ConnectionInstalling/Replacing the Battery Level RangeBattery Status Indicator Initial lighting and gas flame adjustmentsElectronic Ignition System While a knob is Then Lite position, ifIf the low flame needs adjusting If the flame needs adjustingCheck Operation of Cooktop Burners Check Operation of Oven/Broil BurnerIf range does not operate, check the following Complete InstallationIf you need Assistance or Service To Convert Gas Pressure Regulator GAS ConversionsLP Gas Conversion To Convert Surface Burners To Convert Oven Burner Complete ConversionNatural Gas Conversion Std Burner Natural gas oven orifice spud stamped with Page W10533016A