Whirlpool W10153329A Installation Requirements, Tools and Parts, Location Requirements

Page 4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■Level

■3/8" drive ratchet

■Tape measure

■Flat-blade screwdriver

■Phillips screwdriver

■Hand or electric drill

■Slip-joint pliers

■7 mm combination wrench

■Pipe wrench

■1/8" (3.2 mm) drill bit (for wood floors)

■3/16" (4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors)

■Pipe joint compound resistant to LP gas

■Non-corrosive leak-detection solution

Parts supplied

Check that all parts are included.

A

B

C

A.Anti-tip bracket

B.Plastic anchors (2)

C.#10 x 1-1/2”screws (2)

■Literature bag.

■Conversion orifice spuds (inside literature bag).

■Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the oven frame behind the left side of the broiler door.

Model/serial rating plate location

■The range should be located for convenient use in the kitchen.

■Recessed installations must provide complete enclosure of the sides and rear of the range.

■To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■All openings in the wall or floor where range is to be installed must be sealed.

■Do not seal the range to the side cabinets.

■Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

■The floor anti-tip bracket must be installed. To install the anti-tip bracket shipped with the range, see “Install Anti-Tip Bracket” section.

■Grounded electrical supply is required. See “Electrical Requirements” section. Proper gas supply connection must be available. See “Gas Supply Requirements” section.

■Contact a qualified floor covering installer to check that the floor covering can withstand at least 200°F (93°C).

■Use an insulated pad or 1/4" (0.64 cm) plywood under range if installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, deliminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperature of 194ºF (90ºC).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

Mobile home installations require:

■When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Installation Instructions 30 76.2 CM Freestanding GAS Range Range Safety ÍndiceWhat to do if YOU Smell GAS Tools and Parts Installation RequirementsLocation Requirements Product Dimensions Installation ClearancesElectrical Requirements Gas Supply RequirementsType of Gas Gas Supply LineBurner Input Requirements Gas Supply Pressure TestingGas Pressure Regulator Install Anti-Tip Bracket Installation InstructionsUnpack Range Verify Anti-Tip Bracket Location Level RangeMake Gas Connection Typical rigid pipe connectionIf the low flame needs adjusting Check OperationComplete Connection Electronic Ignition SystemComplete Installation Check Operation of Oven/Broil BurnerGAS Conversions LP Gas ConversionTo Convert Gas Pressure Regulator To Convert Surface BurnersTo Convert Oven Burner Complete ConversionFor TGP310 models Natural Gas Conversion Remove burner grates, burner caps, and burnersNatural gas oven orifice spud stamped with Page Seguridad DE LA Estufa Su seguridad y la seguridad de los demás es muy importantePasos QUE Usted Debe Seguir SI Huele a GAS Herramientas y piezas Requisitos DE InstalaciónRequisitos de ubicación Espacios libres para instalación Las instalaciones en casas rodantes necesitanMedidas del producto Requisitos eléctricos Requisitos del suministro de gasTipo de gas Gas naturalLínea de suministro de gas Regulador de la presión de gasRequisitos de entrada del quemador Prueba de presión del suministro de gasDesempaque la estufa Instrucciones DE InstalaciónInstalación del soporte anti-vuelco Nivelación de la estufa Conexión del suministro de gasVerificación de la ubicación del soporte Anti-vuelco Conexión típica de la tubería rígidaVerifique el funcionamiento Complete la conexiónSistema de encendido electrónico Conexión flexible típicaVerifique el funcionamiento del quemador de asar/del horno Si la llama baja necesita ajustarseControl electrónico del horno en algunos modelos Control del panel múltiple del horno en algunos modelosComplete la instalación Si la llama necesita ajustarseAjuste el obturador de aire Si la estufa no funciona, revise lo siguienteConversiones DE GAS Conversión de gas LPCómo convertir el regulador de la presión del gas Dé vuelta a la tapa para que quede visible LPCómo convertir los quemadores de superficie Cómo convertir el quemador del hornoSaque la parrilla, las tapas del quemador y los quemadores Para los modelos TGP310Complete la conversión Conversión de gas naturalCómo convertir los quemadores de la superficie Desenchufe o desconecte el suministro de energíaObturador de airer Whirlpool Corporation

W10153329A specifications

The Whirlpool W10153329A is an innovative and highly functional appliance designed to enhance kitchen efficiency and user convenience. This model stands out in the crowded market of kitchenware, particularly for its versatile features and cutting-edge technologies.

One of the defining characteristics of the W10153329A is its impressive capacity. With ample space for various kitchen tasks, it can accommodate a wide range of food items, making meal preparation faster and more convenient. This large capacity is perfect for families or individuals who regularly entertain guests, allowing for the preparation of larger quantities of food or multiple dishes simultaneously.

In terms of design, the Whirlpool W10153329A boasts a sleek and modern aesthetic that seamlessly blends with contemporary kitchen décor. The stainless steel finish not only enhances its visual appeal but also contributes to its durability, ensuring that it withstands the rigors of daily use while maintaining its polished look. The appliance features intuitive controls, making it easy for users to navigate settings and customize their cooking experience according to their needs.

Another significant aspect of the W10153329A is its incorporation of innovative cooking technologies. It utilizes advanced heating elements that promote even cooking and reduce cooking times, ensuring that meals are prepared quickly without sacrificing quality. The appliance is also equipped with smart technology that allows users to monitor and control cooking parameters remotely, making it possible to start or adjust settings from anywhere within the home through a smartphone app. This connectivity enhances the overall user experience, providing a level of convenience that is increasingly sought after in modern kitchen appliances.

Safety features are also paramount in the design of the Whirlpool W10153329A. It includes built-in sensors that automatically shut off the appliance if it detects an unsafe operating condition, reducing the risk of accidents in the kitchen. Moreover, the user-friendly interface clearly displays all necessary information, helping users to track cooking progress and settings easily.

In conclusion, the Whirlpool W10153329A is a multi-functional kitchen appliance that combines style, efficiency, and advanced technology. Its spacious capacity, sleek finish, innovative cooking capabilities, and safety features make it an excellent choice for anyone looking to elevate their culinary experience. Whether for everyday cooking or special culinary projects, this model stands as a reliable and efficient option for modern kitchens.
Top Page Image Contents